Hand Held Products 600, 800 Changing the Output Options, Display Options, Parameter Result Lines

Page 36

3.Set the cursor on the asterisk next to Scanning Options and then press

SELECT.

A menu that begins with Beeper Pitch appears.

4.To make any necessary changes:

•To change the beeper pitch, set the cursor on the asterisk next to Beeper and then press SELECT or →. The cursor moves to the right of the term Pitch. Press ↑ and ↓ until you hear the beeper pitch you want. To save the selection, press SELECT or ←. The cursor moves back to the asterisk next to Beeper.

•To change the Extended Accuracy setting, set the cursor on the asterisk next to Extended Accur and press SELECT or →. The cursor moves to the right of Accur. Press ↑ and ↓ until the number of scans

you want for the average appears. To save the selection, press SELECT or ←. The cursor moves to the asterisk next to Extended.

•To change the decoding direction setting, set the cursor on the asterisk next to Decoding and then press SELECT or →. The setting changes between BothWays and FwdOnly!.

•When you exit any menu, all the displayed parameter choices are saved.

5.To return to the previous menu, press POWER.

To scan a symbol, set the wand on the symbol’s quiet zone.

Changing the Output Options

The output options include the display options and the print options.

Display Options

The display options include:

•Upper Parameter Result Line display

•Lower Parameter Result Line display

•Error Override display

•LEDs either display ISO/IEC Grade or indicate bar growth or loss

The display options allow you to set the two types of results that are most important to you in the upper and lower parameter result lines so they appear immediately after a scan. (The upper parameter result line is the third line of the display and the lower line is the fourth or bottom line of the display.) Then, by pressing a few buttons, you can review all the other results.

Parameter Result Lines

On the parameter lines, you can display either the result defaults set at the factory, or results you select.

•For traditional pass/fail criteria, the factory-set defaults are PCS and AvgBar.

•For ISO/IEC criteria, the factory-set defaults are Decodability and Modulation.

3 - 12

Quick Check® 600/800 Series User’s Guide

Page 35 Page 37
Image 36
Page 35 Page 37
Contents User’s Guide Disclaimer For European Community UsersWaste Electrical and Electronic Equipment Information Table of Contents Reviewing Scan Data Saving and Printing Chapter Customer Support Getting Started About This GuideSymbolDescription Power or Select or ↑, ↓, ←, → Unpacking the Quick Check 600/800 VerifierTerm in manual Term in software Noting the Verifier’s Features Quick Check 600/800 VerifierEAN/UPC Special Features DisplayLEDs ButtonsPorts Specifications Installing the BatteriesSpecification To Install the Batteries Charging the BatteriesTo charge the batteries Turning the Unit On and Off To turn on the unitNo Printer Attached, then refer to .a Quick Check 600/800 Series User’s Guide Calibrating the Quick Check 600/800 Verifier To turn off the unitTo calibrate the Quick Check 600/800 Verifier To scan properly using a pen wand To scan properly using a mouse wandProperly Scanning With the Unit Cleaning the Wand Accessories and OptionsItem/DescriptionOrder code Documentation Quick Check 600/800 Series User’s Guide Quick Start Guide Review the option settings Print your scan resultsChanging the Settings Changing the SpecificationsSymbologies Symbologies Symbology Specifications Symbology Parameters defaults are in boldMagnification Factor Expand U.P.C./EOCheck Options Modes ShownCharacter Font & Tolerances Character Translation Table Code 128, Code 16K, and CodeTo modify the symbology options Wide-to-Narrow RatioFixed Message Length → or SelectIndustry Applications Changing the Test Criteria Scan GradeTo select an application Decodability ISO/IEC gradesNumber of Scans To return to the previous menu, press Power Changing the Scanning OptionsTo change the test criteria Beeper Pitch Extended AccuracyDecode Direction To change the scanning optionsChanging the Output Options Display OptionsParameter Result Lines Print Options AutoPrint/StoreScan Profile To change the output optionsTo change the display options Resetting the Default Settings Locking the SettingsTo reset a unit To change the printout optionsUsing a Command Code About Command CodesC./EAN/JAN Enable On or Off Generic Code SelectionsChoosing a Command Code Customized Command CodesTo use a customized Command Code To create a customized Command CodeTo request a Command Code from Hand Held Products Quick Check 600/800 Series User’s Guide Reviewing Scan Data Reviewing Scan ResultsScan Grades ISO/IEC Symbol Grade Determining the ISO/IEC Symbol Grade Quick Check 600/800 Series User’s Guide To obtain the scan grade and ISO/IEC Symbol grade Reviewing a Scan ExampleQuick Check 600/800 Series User’s Guide LED Display To review data from the last scanAudio Sounds Bar growth LCD bar growth LED lit Tolerance used IndicationReviewing the Dimensional Parameters Errors in Dimensional ParametersParameter Trad’l Parameter ResultTo review the dimensional parameters CalculatingReviewing the Reflectance Parameters Errors in Reflectance Parameters PCSSymbol Contrast, Minimum and Maximum Reflectance To review the reflectance parametersErrors in Format Parameters Reviewing the Format ParametersTo review the format procedures Reviewing MessagesUsing Sstr Codes to Review Data Sstr CodesSstr Code Type Test Criteria Name Using the Quick Check Verifier as a Reflectometer To quickly review data using Sstr CodesTo return the customized display to the default display To customize the result displayTo use the Quick Check Verifier as a static reflectometer Saving and Printing Saving DataChecking the Print Buffer During Operation To save scan dataPrinting Data To check the print buffer during operationTo clear delete the records stored in the memory, press → To print current dataDeleting Stored Data To print stored dataTo stop printing Interfacing With a Computer Reviewing the PrintoutsTo delete stored data QCP and Qchsp Printouts Using the QCP or Qchsp Printing GuidelinesSwitch Position Function To set up the QCP or Qchsp To install or replace the QCP or Qchsp paper rollTo turn on and off the QCP or Qchsp To remove the ribbon from the QCP or Qchsp To perform a QCP or Qchsp self-test Troubleshooting the QCP or Qchsp Quick Check 600/800 Series User’s Guide Background Information General Bar Code InformationSymbology Specifications Symbology Industries OrganizationGS1 formerly UCC and EAN Symbology Characteristics Quick Check 600/800 Series User’s Guide Symbology Character Set Widths How a Bar Code Verifier WorksElement Additional Information Quick Check 600/800 Series User’s Guide Using DataMatch Understanding the DataMatch FeatureDownloading DataMatch Structuring and Loading the Database SYM Identifier CodeDecode To load the database into the verifierQuick Check 600/800 Series User’s Guide Selecting the DataMatch Feature To select DataMatchReviewing DataMatch Results Quick Check 600/800 Series User’s Guide Using a Quick Check 800 Verifier General OperationPercent Decoded/Scanned Mode Reflectance-Based InformationScanProfile Output Print Results Calculate Decoded/Scanned Change Settings Change Settings Test Criteria #Scans/Symbol nnn Error, Application, and Type Messages Type Display Message Printout MessageDatabase ECV /VCVS Bookland Quick Check 600/800 Series User’s Guide Ccbba Hibcc EAN ITF SCS /ITF EAN SCS Quick Check 600/800 Series User’s Guide Flow Charts Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Sstr Codes Quick Check 600/800 Series User’s Guide Special Codes Quick Check 600/800 Series User’s Guide Unrecognized Symbols Unrecognized SymbolsQuick Check 600/800 Series User’s Guide Troubleshooting To restore the displayCustomer Support To check the software versionLatin America Limited Warranty Quick Check 600/800 Series User’s Guide Page Hand Held Products, Inc
Top Page Image Contents