Muratec F-116 Understanding the Status LED, Introducing the useful button, Turning on the machine

Page 22

Understanding the Status LED

The color of the status LED indicates the machine's current status.

STATUS

 

DESCRIPTION

 

 

 

Off

•

The machine is off-line.

 

•

The machine is in power saver mode. When data is received, or any button is pressed,

 

 

it switches to on-line automatically.

Green:

Blinking

When the backlight blinks rapidly, the machine is printing data.

Online

 

 

On

The machine is on-line and can be used.

(

 

 

)

 

 

 

 

 

 

 

 

 

 

Red:

Blinking

• A minor error has occurred and the machine is waiting for the error to be cleared. Check

Error

 

the display message. When the problem is cleared, the machine resumes.

(

 

)

 

• Small amount of toner is left in the cartridge. The estimated cartridge lifea of toner is

 

 

 

 

 

 

 

close. Prepare a new cartridge for replacement. You may temporarily increase the

 

 

 

 

 

 

 

 

 

 

printing quality by redistributing the toner (See "Redistributing toner" on page53).

 

 

 

 

 

 

 

 

 

 

On

• A toner cartridge has almost reached its estimated cartridge lifea. It is recommended to

 

 

 

 

 

replace the toner cartridge (See "Replacing the toner cartridge" on page68).

•A paper jam has occurred (See "Clearing paper jams" on page56).

•The cover is opened. Close the cover.

•There is no paper in the tray. Load paper in the tray.

•The machine has stopped due to a major error. Check the display message (See "Understanding display messages" on page59).

a.Estimated cartridge life means the expected or estimated toner cartridge life, which indicates the average capacity of print-outs and is designed pursuant to ISO/IEC 19752. The number of pages may be affected by operating environment, printing interval, media type, and media size. Some amount of toner may remain in the cartridge even when End of life Replace new cart appears and the printer stops printing

Muratec does not recommend using non-genuine Muratec toner cartridges such as refilled or remanufactured. Muratec cannot guarantee non-genuine Muratec toner cartridge's quality. Service or repair required as a result of using non-genuine Muratec toner cartridges will not be covered under the machine warranty.

Check the message on the display. Follow the instructions in the message or refer to troubleshooting part (See "Understanding display messages" on page59). If the problem persists, call for service.

Power LED

The power LED indicates the machine's on or off.

STATUS

 

DESCRIPTION

 

 

Off

The machine is turned off.

On

•

The machine is in ready mode.

 

•

The machine is in power on.

 

 

 

Introducing the useful button

Menu button

When you want to know the machine status and set your machine to use an advanced feature, click Menu button (See "Machine status and advanced feature" on page42).

Turning on the machine

1.Plug in the power cord.

2.Press (power) on the control panel.

If you want to turn the power off, press this button.

Introduction_ 21

Page 21 Page 23
Image 22
Page 21 Page 23
Contents User Guide Copyright CopyrightContents Resolution Darkness CopyingCleaning the drum Checking display messagesSafety information Safety informationImportant safety symbols Operating environmentOperating method Installation / Moving Maintenance / CheckingSupply usage Regulatory information Laser Safety StatementOzone Safety Regulatory informationCorrect disposal of batteries in this product RecyclingTaiwan only Germany only Fax Branding Radio Frequency EmissionsRussia only FCC Information to the UserReplacing the Fitted Plug for UK Only Ringer Equivalence NumberYou should also know that Green and Yellow Earth Important warningBrown Live China only About this user’s guide About this user’s guideConvention Conventio Description ExampleMaterial Name Description Quick Install GuideFinding more information Instructions in the guide to prepare the machineSpecial Features Features of your new productFeatures of your new product Front view IntroductionMachine overview IntroductionRear view Control panel overview Introducing the useful button Power LEDUnderstanding the Status LED Turning on the machineSetting up the hardware Basic setupBasic setup Setting sounds Setting the date and timeChanging the clock mode Changing the display languageKeypad letters and numbers Entering characters using the number keypadEntering alphanumeric characters Correcting numbers or namesUsing the save modes Setting the paperLoading originals Media and trayPreparing originals Document feederSelecting print media Guidelines to select the print mediaCopy mode Media sizes supported in each modeMode Size Source Fax modeLoading paper in the tray TrayLetterhead/ Preprinted paper Setting the paper size and typeUsing the output support SINGLE-SIDED DOUBLE-SIDEDCopying Changing the settings for each copyBasic copy Setting copy timeout Changing the default copy settingsTo scale the copy by directly entering the scale rate Preparing to fax Setting the fax headerFaxing Sending a faxConfirming a transmission Delaying a fax transmissionSending a fax manually Automatic redialingSending a priority fax Adding documents to a reserved delay fax jobCanceling a reserved delay fax job Sending a fax in toll save timeReceiving faxes manually using an extension telephone Receiving manually in Tel modeReceiving automatically in Answering Machine/Fax mode Receiving a faxActivating secure receiving mode Receiving faxes using Drpd modeReceiving in secure receiving mode Deactivating secure receiving modeAdjusting the document settings Forwarding a fax to other destinationSetting up address book Registering a group dial number Using group dial numbersGroup dial numbers Editing a group dial numberPrinting sent fax report automatically Changing the fax setup options Machine status and advanced featureFax setup Available fax setup optionsUsing the advanced fax settings Advanced fax setting optionsChange Default Copy setupChanging the copy setup options Printing a reportClear All Mem Menu overview Items OptionMachine status and advanced feature Cleaning the outside MaintenanceCleaning a machine Cleaning the insideCleaning the scan unit Maintenance Handling instructions Cleaning the drumStoring the Toner cartridge Use of non-Muratec and refilled toner cartridgeTips for moving & storing your machine Troubleshooting TroubleshootingRedistributing toner Clearing original document jams Input MisfeedExit Misfeed Tips for avoiding paper curlsPressure lever Tips for avoiding paper jams Clearing paper jamsInside the machine Exit areaIf you do not see the jammed paper, go to next step Understanding display messages Message Meaning Suggested SolutionsChecking display messages Assigned Power FailureOperation Not Paper JamPrinting problems Solving other problemsPaper feeding problems Printing quality problemsDropouts Light or faded printToner specks White SpotsBackground scatter Toner smearDefects MisformedCondition SkewCopying problems Condition Suggested SolutionFax problems Available maintenance parts Supplies and accessoriesHow to purchase Supplies and accessoriesParts Replacing the toner cartridgeEnd of life Replace new cart appears on the display Supplies and accessories Environmental specifications SpecificationsHardware specifications Electrical specificationsType Size Dimensions Print media specificationsTRAY1 Glossary Duplex DefaultDot Matrix Printer Duty CycleFuser Unit EthernetEtherTalk GatewayITU-T No chart MAC addressOriginals ModemNetWare PostScriptProtocol PRN fileSubnet Mask UNC Path Toner CartridgeWatermark Index Toner save mode 25 tray Time setting 23 toner cartridgeTurning on the machine Index
Top Page Image Contents