Muratec F-116 manual Storing the Toner cartridge, Cleaning the drum, Handling instructions

Page 52

7.Reconnect the support and the control panel and then close the control panel firmly until it clicks into place.

Cleaning the drum

If there are streaks or spots on your machine, the OPC drum of the cartridge may require cleaning.

1.Before setting the cleaning procedure, make sure that paper is loaded in the machine.

2.Press Menu until Maintenance appears.

3.Press the left/right arrow until Clean Drum appears and press OK.

4.Press the left/right arrow until On appears and press OK.

The machine prints a cleaning page. Toner particles on the drum surface are affixed to the paper.

5.If the problem remains, repeat step 1 through 4.

Storing the Toner cartridge

Toner cartridges contain components that are sensitive to light, temperature, and humidity. Muratec suggests users follow the recommendations to ensure the optimum performance, highest quality, and longest life from your new Muratec toner cartridge.

Store this cartridge in the same environment as the printer it will be used in; this should be in controlled office temperature and humidity conditions. The toner cartridge should remain in its original, unopened package until installation – If original packaging is not available, cover the top opening of the cartridge with paper and store in a dark cabinet.

Opening the cartridge package prior to use dramatically shortens its useful shelf and operating life. Do not store on the floor. If the toner cartridge is removed from the printer, always store the cartridge:

•Inside the protective bag from the original package.

•Store lying flat (not standing on end) with the same side facing up as if they were installed in the machine.

•Do not store consumable in;

-Temperature greater than 40°C (104°F).

-Humidity range less than 20% nor greater than 80%.

-An environment with extreme changes in humidity or temperature.

-Direct sunlight or room light.

-Dusty places.

-A car for a long period of time.

-An environment where corrosive gases are present.

-An environment with salty air.

Handling instructions

•Do not touch the surface of the photosensitive drum in the cartridge.

•Do not expose the cartridge to unnecessary vibrations or shock.

•Never manually rotate the drum, especially in the reverse direction; this can cause internal damage and toner spillage.

Use of non-Muratec and refilled toner cartridge

Muratec does not recommend or approve the use of non-Muratec brand toner cartridges in your printer including generic, store brand, refilled, or remanufactured toner cartridges.

Muratec's warranty does not cover damage to the machine caused by the use of a refilled, remanufactured, or non-Muratec brand toner cartridge.

Estimated cartridge life

Estimated cartridge life (the life of the toner cartridge yield) depends on the amount of toner that print jobs require. The actual print-out number may vary depending on the print density of the pages you print on, operating environment, printing interval, media type, and/or media size. For example, if you print a lot of graphics, the consumption of the toner is high and you may need to change the cartridge more often.

Maintenance_ 51

Page 51 Page 53
Image 52
Page 51 Page 53
Contents User Guide Copyright CopyrightContents Resolution Darkness CopyingCleaning the drum Checking display messagesSafety information Important safety symbolsSafety information Operating environmentOperating method Installation / Moving Maintenance / CheckingSupply usage Laser Safety Statement Ozone SafetyRegulatory information Regulatory informationCorrect disposal of batteries in this product RecyclingTaiwan only Radio Frequency Emissions Russia onlyGermany only Fax Branding FCC Information to the UserReplacing the Fitted Plug for UK Only Ringer Equivalence NumberYou should also know that Green and Yellow Earth Important warningBrown Live China only About this user’s guide ConventionAbout this user’s guide Conventio Description ExampleQuick Install Guide Finding more informationMaterial Name Description Instructions in the guide to prepare the machineSpecial Features Features of your new productFeatures of your new product Introduction Machine overviewFront view IntroductionRear view Control panel overview Power LED Understanding the Status LEDIntroducing the useful button Turning on the machineSetting up the hardware Basic setupBasic setup Setting the date and time Changing the clock modeSetting sounds Changing the display languageEntering characters using the number keypad Entering alphanumeric charactersKeypad letters and numbers Correcting numbers or namesUsing the save modes Setting the paperMedia and tray Preparing originalsLoading originals Document feederSelecting print media Guidelines to select the print mediaMedia sizes supported in each mode Mode Size SourceCopy mode Fax modeLoading paper in the tray TraySetting the paper size and type Using the output supportLetterhead/ Preprinted paper SINGLE-SIDED DOUBLE-SIDEDCopying Changing the settings for each copyBasic copy Setting copy timeout Changing the default copy settingsTo scale the copy by directly entering the scale rate Setting the fax header FaxingPreparing to fax Sending a faxDelaying a fax transmission Sending a fax manuallyConfirming a transmission Automatic redialingAdding documents to a reserved delay fax job Canceling a reserved delay fax jobSending a priority fax Sending a fax in toll save timeReceiving manually in Tel mode Receiving automatically in Answering Machine/Fax modeReceiving faxes manually using an extension telephone Receiving a faxReceiving faxes using Drpd mode Receiving in secure receiving modeActivating secure receiving mode Deactivating secure receiving modeAdjusting the document settings Forwarding a fax to other destinationSetting up address book Using group dial numbers Group dial numbersRegistering a group dial number Editing a group dial numberPrinting sent fax report automatically Machine status and advanced feature Fax setupChanging the fax setup options Available fax setup optionsUsing the advanced fax settings Advanced fax setting optionsCopy setup Changing the copy setup optionsChange Default Printing a reportClear All Mem Menu overview Items OptionMachine status and advanced feature Maintenance Cleaning a machineCleaning the outside Cleaning the insideCleaning the scan unit Maintenance Cleaning the drum Storing the Toner cartridgeHandling instructions Use of non-Muratec and refilled toner cartridgeTips for moving & storing your machine Troubleshooting TroubleshootingRedistributing toner Clearing original document jams Input MisfeedExit Misfeed Tips for avoiding paper curlsPressure lever Tips for avoiding paper jams Clearing paper jamsInside the machine Exit areaIf you do not see the jammed paper, go to next step Understanding display messages Message Meaning Suggested SolutionsChecking display messages Power Failure Operation NotAssigned Paper JamSolving other problems Paper feeding problemsPrinting problems Printing quality problemsLight or faded print Toner specksDropouts White SpotsToner smear DefectsBackground scatter MisformedCondition SkewCopying problems Condition Suggested SolutionFax problems Supplies and accessories How to purchaseAvailable maintenance parts Supplies and accessoriesParts Replacing the toner cartridgeEnd of life Replace new cart appears on the display Supplies and accessories Specifications Hardware specificationsEnvironmental specifications Electrical specificationsType Size Dimensions Print media specificationsTRAY1 Glossary Default Dot Matrix PrinterDuplex Duty CycleEthernet EtherTalkFuser Unit GatewayITU-T No chart MAC addressModem NetWareOriginals PostScriptProtocol PRN fileSubnet Mask UNC Path Toner CartridgeWatermark Index Toner save mode 25 tray Time setting 23 toner cartridgeTurning on the machine Index
Top Page Image Contents