Muratec F-116 Setting the paper size and type, Using the output support, Tray1 Face down Face up

Page 31

Letterhead/ Preprinted paper

	SINGLE-SIDED	DOUBLE-SIDED

Tray1	Face down	Face up

•Letterhead/ Preprinted paper must be printed with heat-resistant ink that will not melt, vaporize, or release hazardous emissions when subjected to the machine’s fusing temperature for 0.1 second. Check your machine’s specification to view the fusing temperature (about 170°C (338 °F)).

•Letterhead/ Preprinted paper ink must be non-flammable and should not adversely affect machine rollers.

•Forms and letterhead should be sealed in a moisture-proof wrapping to prevent changes during storage.

•Before you load letterhead/preprinted paper, verify that the ink on the paper is dry. During the fusing process, wet ink can come off preprinted paper, reducing print quality.

Setting the paper size and type

After loading paper in the paper tray, set the paper size and type using the control panel. These settings will apply to copy and fax modes.

Setting the paper size

1.Press Menu until Paper Setting appears.

2.Press the left/right arrow until Paper Size appears and press OK.

3.Press OK.

4.Press the left/right arrow to select the paper size you want.

5.Press OK to save the selection.

6.Press Stop/Clear to return to ready mode.

Setting the paper type

1.Press Menu until Paper Setting appears.

2.Press the left/right arrow until Paper Type appears and press OK.

3.Press the left/right arrow to select the paper type you want.

4.Press OK to save the selection.

5.Press Stop/Clear to return to ready mode.

Using the output support

The surface of the output tray may become hot if you print a large number of pages at once. Make sure that you do not touch the surface, and do not allow children near it.

The printed pages stack on the output support, and the output support will help the printed pages to align. The printer sends output to the output tray by default. To use the output tray, make sure that the rear cover is closed.

If you are using A5 paper, fold the output tray. Otherwise, printed pages might be mis-alligned or jammed.

Media and tray_ 30

Image 31

Contents User Guide Copyright CopyrightContents Copying Resolution DarknessChecking display messages Cleaning the drumOperating environment Safety informationImportant safety symbols Safety informationOperating method Maintenance / Checking Installation / MovingSupply usage Regulatory information Laser Safety StatementOzone Safety Regulatory informationCorrect disposal of batteries in this product RecyclingTaiwan only FCC Information to the User Radio Frequency EmissionsRussia only Germany only Fax BrandingReplacing the Fitted Plug for UK Only Ringer Equivalence NumberYou should also know that Green and Yellow Earth Important warningBrown Live China only Conventio Description Example About this user’s guideConvention About this user’s guideInstructions in the guide to prepare the machine Quick Install GuideFinding more information Material Name DescriptionSpecial Features Features of your new productFeatures of your new product Introduction IntroductionMachine overview Front viewRear view Control panel overview Turning on the machine Power LEDUnderstanding the Status LED Introducing the useful buttonSetting up the hardware Basic setupBasic setup Changing the display language Setting the date and timeChanging the clock mode Setting soundsCorrecting numbers or names Entering characters using the number keypadEntering alphanumeric characters Keypad letters and numbersSetting the paper Using the save modesDocument feeder Media and trayPreparing originals Loading originalsGuidelines to select the print media Selecting print mediaFax mode Media sizes supported in each modeMode Size Source Copy modeTray Loading paper in the traySINGLE-SIDED DOUBLE-SIDED Setting the paper size and typeUsing the output support Letterhead/ Preprinted paperCopying Changing the settings for each copyBasic copy Setting copy timeout Changing the default copy settingsTo scale the copy by directly entering the scale rate Sending a fax Setting the fax headerFaxing Preparing to faxAutomatic redialing Delaying a fax transmissionSending a fax manually Confirming a transmissionSending a fax in toll save time Adding documents to a reserved delay fax jobCanceling a reserved delay fax job Sending a priority faxReceiving a fax Receiving manually in Tel modeReceiving automatically in Answering Machine/Fax mode Receiving faxes manually using an extension telephoneDeactivating secure receiving mode Receiving faxes using Drpd modeReceiving in secure receiving mode Activating secure receiving modeForwarding a fax to other destination Adjusting the document settingsSetting up address book Editing a group dial number Using group dial numbersGroup dial numbers Registering a group dial numberPrinting sent fax report automatically Available fax setup options Machine status and advanced featureFax setup Changing the fax setup optionsAdvanced fax setting options Using the advanced fax settingsPrinting a report Copy setupChanging the copy setup options Change DefaultClear All Mem Items Option Menu overviewMachine status and advanced feature Cleaning the inside MaintenanceCleaning a machine Cleaning the outsideCleaning the scan unit Maintenance Use of non-Muratec and refilled toner cartridge Cleaning the drumStoring the Toner cartridge Handling instructionsTips for moving & storing your machine Troubleshooting TroubleshootingRedistributing toner Input Misfeed Clearing original document jamsExit Misfeed Tips for avoiding paper curlsPressure lever Clearing paper jams Tips for avoiding paper jamsExit area Inside the machineIf you do not see the jammed paper, go to next step Understanding display messages Message Meaning Suggested SolutionsChecking display messages Paper Jam Power FailureOperation Not AssignedPrinting quality problems Solving other problemsPaper feeding problems Printing problemsWhite Spots Light or faded printToner specks DropoutsMisformed Toner smearDefects Background scatterSkew ConditionCondition Suggested Solution Copying problemsFax problems Supplies and accessories Supplies and accessoriesHow to purchase Available maintenance partsParts Replacing the toner cartridgeEnd of life Replace new cart appears on the display Supplies and accessories Electrical specifications SpecificationsHardware specifications Environmental specificationsType Size Dimensions Print media specificationsTRAY1 Glossary Duty Cycle DefaultDot Matrix Printer DuplexGateway EthernetEtherTalk Fuser UnitMAC address ITU-T No chartPostScript ModemNetWare OriginalsProtocol PRN fileSubnet Mask UNC Path Toner CartridgeWatermark Index Toner save mode 25 tray Time setting 23 toner cartridgeTurning on the machine Index