Muratec F-116 manual Installation / Moving, Maintenance / Checking

Page 8

Installation / Moving

Warning

Do not place the machine in an area with dust, humidity or water leaks.

► This could result in electric shock or fire.

Caution

When moving the machine, turn the power off and disconnect all cords; then lift the machine with at least two people.

►The machine could fall, causing human injury or machine damage.

Do not place the machine on an unstable surface.

►The machine could fall, causing human injury or machine damage.

The machine should be connected to

the power level which is specified on the label.

►If you are unsure and want to check the power level you are using, contact the electrical utility company.

Use only No.26 AWGa or larger, telephone line cord, if necessary.

►Otherwise, it can cause damage to the machine.

a.AWG: American Wire Gauge

Do not put a cover over the machine or place it in an airtight location, such as a closet.

►If the machine is not well-ventilated, this could result in fire.

Make sure you plug the power cord into a grounded electrical outlet.

►Otherwise, this could result in electric shock or fire.

Do not overload wall outlets and extension cords.

►This can diminish performance, and could result in electric shock or fire.

Use the power cord supplied with your machine for safe operation. If you are using a cord which is longer than 2 meters (79”) with a 140V machine, then the gauge should be 16 AWG or larger.

►Otherwise, it can cause damage to the machine, and could result in electric shock or fire.

Maintenance / Checking

Caution

Unplug this product from the wall outlet before cleaning the inside of the machine. Do not clean the machine with benzene, paint thinner or achol; do not spray water directly into the machine.

►This could result in electric shock or fire.

When you are working inside the machine replacing supplies or cleaning the inside, do not operate the machine.

►You may get injured.

Keep cleaning supplies away from children.

►Children may get hurt.

Do not disassemble, repair or rebuild the machine by yourself.

►It can cause damage to the machine. Call a certified technician when the machine needs repair.

Safety information_ 7

Image 8

Contents User Guide Copyright CopyrightContents Resolution Darkness CopyingCleaning the drum Checking display messagesSafety information Important safety symbolsSafety information Operating environmentOperating method Installation / Moving Maintenance / CheckingSupply usage Laser Safety Statement Ozone SafetyRegulatory information Regulatory informationTaiwan only RecyclingCorrect disposal of batteries in this product Radio Frequency Emissions Russia onlyGermany only Fax Branding FCC Information to the UserYou should also know that Ringer Equivalence NumberReplacing the Fitted Plug for UK Only Brown Live Important warningGreen and Yellow Earth China only About this user’s guide ConventionAbout this user’s guide Conventio Description ExampleQuick Install Guide Finding more informationMaterial Name Description Instructions in the guide to prepare the machineFeatures of your new product Features of your new productSpecial Features Introduction Machine overviewFront view IntroductionRear view Control panel overview Power LED Understanding the Status LEDIntroducing the useful button Turning on the machineBasic setup Basic setupSetting up the hardware Setting the date and time Changing the clock modeSetting sounds Changing the display languageEntering characters using the number keypad Entering alphanumeric charactersKeypad letters and numbers Correcting numbers or namesUsing the save modes Setting the paperMedia and tray Preparing originalsLoading originals Document feederSelecting print media Guidelines to select the print mediaMedia sizes supported in each mode Mode Size SourceCopy mode Fax modeLoading paper in the tray TraySetting the paper size and type Using the output supportLetterhead/ Preprinted paper SINGLE-SIDED DOUBLE-SIDEDBasic copy Changing the settings for each copyCopying To scale the copy by directly entering the scale rate Changing the default copy settingsSetting copy timeout Setting the fax header FaxingPreparing to fax Sending a faxDelaying a fax transmission Sending a fax manuallyConfirming a transmission Automatic redialingAdding documents to a reserved delay fax job Canceling a reserved delay fax jobSending a priority fax Sending a fax in toll save timeReceiving manually in Tel mode Receiving automatically in Answering Machine/Fax modeReceiving faxes manually using an extension telephone Receiving a faxReceiving faxes using Drpd mode Receiving in secure receiving modeActivating secure receiving mode Deactivating secure receiving modeAdjusting the document settings Forwarding a fax to other destinationSetting up address book Using group dial numbers Group dial numbersRegistering a group dial number Editing a group dial numberPrinting sent fax report automatically Machine status and advanced feature Fax setupChanging the fax setup options Available fax setup optionsUsing the advanced fax settings Advanced fax setting optionsCopy setup Changing the copy setup optionsChange Default Printing a reportClear All Mem Menu overview Items OptionMachine status and advanced feature Maintenance Cleaning a machineCleaning the outside Cleaning the insideCleaning the scan unit Maintenance Cleaning the drum Storing the Toner cartridgeHandling instructions Use of non-Muratec and refilled toner cartridgeTips for moving & storing your machine Redistributing toner TroubleshootingTroubleshooting Clearing original document jams Input MisfeedPressure lever Tips for avoiding paper curlsExit Misfeed Tips for avoiding paper jams Clearing paper jamsInside the machine Exit areaIf you do not see the jammed paper, go to next step Checking display messages Message Meaning Suggested SolutionsUnderstanding display messages Power Failure Operation NotAssigned Paper JamSolving other problems Paper feeding problemsPrinting problems Printing quality problemsLight or faded print Toner specksDropouts White SpotsToner smear DefectsBackground scatter MisformedCondition SkewCopying problems Condition Suggested SolutionFax problems Supplies and accessories How to purchaseAvailable maintenance parts Supplies and accessoriesEnd of life Replace new cart appears on the display Replacing the toner cartridgeParts Supplies and accessories Specifications Hardware specificationsEnvironmental specifications Electrical specificationsTRAY1 Print media specificationsType Size Dimensions Glossary Default Dot Matrix PrinterDuplex Duty CycleEthernet EtherTalkFuser Unit GatewayITU-T No chart MAC addressModem NetWareOriginals PostScriptSubnet Mask PRN fileProtocol Watermark Toner CartridgeUNC Path Index Turning on the machine Index Time setting 23 toner cartridgeToner save mode 25 tray