Trango Broadband M2400S user manual Subscriber Unit Basic Settings

Page 29

Basic Configuration via CLI

In this example, SU #5’s CIR downstream is set to 128 and CIR upstream is set to 256. MIR upstream and downstream are set to 5000.

To change the default CIR/MIR values, use the following command:

sudb defaultcirmir <default cir dn> <default cir up> <default mir dn> <default mir up>

Example:

#>sudb defaultcirmir 256 256 512 512

To view the entries in the SUDB, type the command sudb view.

To save the changes you have made to the SUDB, type save sudb

Other important SUDB related commands are sudb delete, sudb gid, and sudb modify. See Appendix A for descriptions of these commands.

!Important! After updating the SUDB, type the command save sudb to save the SUDB. If you do not save the SUDB file will revert back to its previous state after power cycle or reboot.

!Important! SUs using SU to SU communication must be on the same subnet.

Subscriber Unit Basic Settings

Once logged into the SU, you can receive a comprehensive snapshot of the system’s configuration info and status by typing the command sysinfo.

#> sysinfo

[Hardware Version] 0006

[FPGA Version] 04042201 [Checksum] 47231EEE

[Firmware Version] SU 1p0x8H0006D04061502 [Checksum] 6DDF232C [Device ID] 00 01 DE 19 F0 A4 [S/N] 01700004

[Base ID] 1234 [AP ID] 01 [SU ID] 1 [System Up Time] 0 day(s) 05:14:51 [Opmode] on [Default Opmode] on

[IP] 10.8.1.234 [Subnet Mask] 255.255.255.192 [Gateway] 10.8.1.193 [Login Password] RW

[Httpd Port] 80 [Httpd Status] listen

[Telnetd Port] 23 [Telnetd Status] connected (10.8.0.60,1738) [Tftpd] disabled

'[RF Tx Power] 22 dBm [RF Rx Threshold] -98 dBm

[Ch#01] 2405 Mhz [Ch#02] 2415 Mhz [Ch#03] 2425 Mhz [Ch#04] 2435 Mhz

[Ch#05] 2445 Mhz [Ch#06] 2455 Mhz [Ch#07] 2465 Mhz [Ch#08] 2475 Mhz [Default Channel] 1 h [Active Channel] 1 v [Associated] Y

[Broadcast Packet] block [Auto Scan AP] on [TCP/IP for AP] on [TCP/IP for Local Eth] on

[Remarks]

[RF Rx] 3 kbps [RF Tx] 2 kbps [Eth Rx] 0 kbps [Eth Tx] 0 kbps [ARQ RF Tx Retry] 0 [ARQ RF Tx Retry Maxed Out] 0

Many of these parameters can be changed by the user. A description of each of these changeable parameters, along with the related command, is shown in the table below.

Trango Broadband Wireless — User Manual M2400S Rev A

Page 25

Image 29

Contents M2400S GHz Wireless Broadband System Table of Contents Table of Figures Preface Warranty Information Firmware NotificationsFCC Information CanadaOverview IntroductionSmartPolling & Bandwidth Throttling Auto-retransmit Feature ARQM2400S AP and SU Hardware Components Hardware OverviewGetting Started Connections and PowerRadio Management Concepts Wiring DiagramOpmode Browser InterfaceBrowser Interface Login Primary Features and Pages of the Browser Interface Telnet ip address of radio Command Line InterfaceTroubleshooting This section you will Basic Configuration via Browser InterfaceConfiguring the AP Subscriber Unit Database Sudb CIR Down Creating an SU in the SudbDefault Opmode Configure Other Basic AP ParametersIP Address, Subnet Mask, and Gateway Active Channel/PolarizationBasic Configuration via Browser Interface SU Basic Setup Configure Basic SU ParametersLink Control LED SummaryRF Link Loopback Test SU Ranging Test Advanced SetupOther Key Parameters Site Survey Set baseid baseid Basic Configuration via CLIAccess Point Basic Settings Set defaultopmode on time sec Set defaultopmode on or offIpconfig new ip new subnet mask new Set apid apid 00-FF in HEXSw 0 onoff default is on Power set minmaxdBmOn/off command Sw 3 onoff default is offSw 7 onoff default is on Subscriber Unit Database SettingsRemarks remarks Sudb add suid prreg device id suid SU IDSubscriber Unit Basic Settings Targetap apid SU System Information Parameters and Related CommandsSw 0 onoff Antenna h v eSw 1 onoff Sw 2 onoffPart Number QTY Mounting HardwareCabling and Grounding Considerations Installation NotesSite Selection Command survey time antennaDeployment Site Survey Example AP Search and SU Antenna AlignmentAP Search Rssi Command for Antenna AlignmentSu ping suid Link Management CommandsSU Alignment Using LEDs Su linktest suid Su suidSu testrflink suid Radio Management Access Via TCP/IP ARQ with Selected Repeat and Multirate FeatureManagement SU Management from APSu ipconfig suid new ip new subnet new gateway Loading Multiple SU’s into Sudb using Dload CommandSu password suid all rw ro new password new password Objects for Monitoring and Control Snmp SetupSU Bandwidth Monitoring AP Bandwidth MonitoringManagement Command Radio Description Access Appendix a Command Set ReferenceReboot unit Ro/rw Remarks Su ipconfig suid new IP new Default = Tftpd Receiver Specifications Appendix B SpecificationsRadio Transmit Specifications Power Specifications Ethernet I/O SpecificationsMechanical and Environmental Specifications Standard External Power SupplyIntegrated Antenna SU Standard External Power-over-Ethernet Junction BoxIntegrated Antenna AP