Trango Broadband M2400S Ethernet I/O Specifications, Data Input/Output, Power Specifications

Page 49

LO stability:	+/- 2.5 ppm PLL stabilized over temperature
Ethernet I/O Specifications
Data Input/Output:
Connector:	Shielded RJ-45 Jack
Signaling Format:	IEEE802.3i (10baseT) and IEEE802.3u (100baseT) compliant
Filtering:	PPPoE per RFC 2516 (SU only)
Auto-Negotiation:	Fully supports IEEE802.3-2002 Sect. 2 Clause 28
Bridging Frame Size:	60 to 1600 bytes
Mngmt Frames:	60 to 1472 bytes. (includes PING, TELNET, TFTP, HTTP)
Protection:	Bi-directional transient voltage protection diodes on all data lines
	compliance with:
	IEC61000-4-2 (ESD)
	IEC61000-4-4 (EFT)
	IEC61000-4-5 (Lightning)
Power Specifications
Input Voltage:	Input voltage range at unit is 10.5 VDC to 24 VDC max

Power is supplied via unused pins of the RJ-45 Jack. Power is injected into Ethernet cable using a junction box (J-Box) provided.

Current Cons.:	500 mA in transmit and receive modes at max power using 20 V
	standard adapter (10 W) and 10 ft cable from J-Box to unit
Protection:	28 volt Transient Voltage Suppression (TVS) diode on power input
	Note: Voltages above 28 volts will cause damage to unit.
Mechanical and Environmental Specifications
General
Material:	High temp polycarbonate radome and diecast metal enclosure
Size:	12.5” x 8” x 2.75” including mounting studs
Weight:	4 lb
Mounting:	2 U-Brackets, all-thread rod, nuts and washers
Connectors/Indicators
RF Output:	Integral internal patch antenna per Part 15C, 15.203
	External RP-SMA-f connector for external antenna

FCC Compliance: The transceiver complies with the following:

FCC Part 15.247

FCC Part 15.207(a)

Environmental
Operating Temp:	-40 to 60 deg C
Storage:	-40 to 85 deg C
Humidity:	100 % when sealed properly
NEMA Rating: NEMA 4
Shock:	Sustain 3 axis drop from 5 feet
Standard External Power Supply
20 Volt DC Power adapter and J-Box supplied with product.

Trango Broadband Wireless — User Manual M2400S Rev. A		Page 45

Image 49

Contents M2400S GHz Wireless Broadband System Table of Contents Table of Figures Preface Warranty Information Firmware NotificationsFCC Information CanadaOverview IntroductionSmartPolling & Bandwidth Throttling Auto-retransmit Feature ARQM2400S AP and SU Hardware Components Hardware OverviewGetting Started Connections and PowerRadio Management Concepts Wiring DiagramOpmode Browser InterfaceBrowser Interface Login Primary Features and Pages of the Browser Interface Telnet ip address of radio Command Line InterfaceTroubleshooting Configuring the AP Subscriber Unit Database Sudb Basic Configuration via Browser InterfaceThis section you will CIR Down Creating an SU in the SudbDefault Opmode Configure Other Basic AP ParametersIP Address, Subnet Mask, and Gateway Active Channel/PolarizationBasic Configuration via Browser Interface SU Basic Setup Configure Basic SU ParametersLink Control LED SummaryRF Link Loopback Test SU Ranging Test Advanced SetupOther Key Parameters Site Survey Access Point Basic Settings Basic Configuration via CLISet baseid baseid Set defaultopmode on time sec Set defaultopmode on or offIpconfig new ip new subnet mask new Set apid apid 00-FF in HEXSw 0 onoff default is on Power set minmaxdBmOn/off command Sw 3 onoff default is offSw 7 onoff default is on Subscriber Unit Database SettingsRemarks remarks Sudb add suid prreg device id suid SU IDSubscriber Unit Basic Settings Targetap apid SU System Information Parameters and Related CommandsSw 0 onoff Antenna h v eSw 1 onoff Sw 2 onoffPart Number QTY Mounting HardwareCabling and Grounding Considerations Installation NotesDeployment Command survey time antennaSite Selection Site Survey Example AP Search and SU Antenna AlignmentAP Search Rssi Command for Antenna AlignmentSU Alignment Using LEDs Link Management CommandsSu ping suid Su linktest suid Su suidSu testrflink suid Radio Management Access Via TCP/IP ARQ with Selected Repeat and Multirate FeatureManagement SU Management from APSu password suid all rw ro new password new password Loading Multiple SU’s into Sudb using Dload CommandSu ipconfig suid new ip new subnet new gateway Objects for Monitoring and Control Snmp SetupSU Bandwidth Monitoring AP Bandwidth MonitoringManagement Command Radio Description Access Appendix a Command Set ReferenceReboot unit Ro/rw Remarks Su ipconfig suid new IP new Default = Tftpd Radio Transmit Specifications Appendix B SpecificationsReceiver Specifications Power Specifications Ethernet I/O SpecificationsMechanical and Environmental Specifications Standard External Power SupplyIntegrated Antenna AP Standard External Power-over-Ethernet Junction BoxIntegrated Antenna SU