Appendix A | Command Set Reference |
|
| |||
| (ro = read only access, rw = read write access) |
|
| |||
|
|
|
|
| ||
Command |
| Radio | Description | Access | ||
? |
|
| AP/SU | Display complete list of commands and syntax | ro/rw | |
|
|
|
|
| ||
? <command> |
| AP/SU | Display specific command syntax | ro/rw | ||
antenna |
| AP/SU | Display current antenna setting | ro/rw | ||
|
|
|
| (h=horizontal, v=vertical, e=external ) |
|
|
antenna <e h v> |
| AP/SU | Select antenna mode | rw | ||
|
|
|
| (h=horizontal, v=vertical, e=external) |
|
|
aprssi <ch#> <antenna, h v e> |
| AP/SU | Scan two strongest APs | ro/rw | ||
|
|
|
| (Opmode “OFF” only) |
|
|
apsearch |
| AP/SU | Scan all channels to look for APs | ro/rw | ||
|
|
|
| (Opmode “OFF” only) |
|
|
arq |
| AP/SU | Display current ARQ settings | ro/rw | ||
arq <onoff> |
| AP/SU | Enable/disable ARQ | rw | ||
bye |
| AP/SU | Same as “logout” | ro/rw | ||
eth link |
| AP/SU | Display current Ethernet setting | ro/rw | ||
eth link <100fdx100hdx10fdx10hdxaneg> | AP/SU | Change Ethernet duplex setting | rw | |||
exit |
| AP/SU | Same as “logout” | ro/rw | ||
freq |
| AP/SU | Display current channel | ro/rw | ||
freq <ch#> |
| AP/SU | Change current channel | rw | ||
freq channeltable |
| AP/SU | Display channel table | ro/rw | ||
freq writechannel [<ch #> <freq>]… |
| AP/SU | Modify center frequency of channel. | rw | ||
|
|
|
| <ch #> = 1..8 |
|
|
|
|
|
| <freq> = 2405..2475 |
|
|
|
|
|
| Note: This command automatically writes to flash memory. |
|
|
help |
| AP/SU | Display complete list of commands and syntax | ro/rw | ||
help <command> |
| AP/SU | Display specific command syntax | ro/rw | ||
ipconfig [<new ip> <new subnet mask> <new | AP/SU | Assign radio’s IP, subnet mask, and gateway IP | rw | |||
gateway>] |
|
|
|
|
| |
linktest <txrxrxtx> [<pkt len, bytes> [<# of | AP/SU | Loopback test to check quality of the wireless link. Variable | ro/rw | |||
pkts> [<# of cycle>]]] |
|
| parameters include: |
|
| |
|
|
|
| pktlen = 64..1760, |
|
|
|
|
|
| # 0 pkts = 1..500 |
|
|
|
|
|
| # of cycles = 1..100000 |
|
|
logout |
| AP/SU | Log out of radio | ro/rw | ||
maclist |
| AP/SU | Display current MAC table (MAC addresses of attached devices) | ro/rw | ||
maclist reset |
| AP/SU | Display or reset current MAC table | ro/rw | ||
mirth |
| AP | Display MIR (Maximum Information Rate) Threshold | ro/rw | ||
mirth <0..3, Mbps> |
| AP | Assign MIR Threshold | rw | ||
|
|
|
| default = 3 Mbps |
|
|
|
|
|
| mirth 0 = Always On |
|
|
|
|
|
| mirth 3 = Disable MIR Threshold |
|
|
opmode |
| AP/SU | Display current Opmode | ro/rw | ||
opmode on [<y>] |
| AP/SU | Set Opmode to be “ON” and use “y” if Opmode is not as same as | ro/rw | ||
|
|
|
| default Opmode |
|
|
password <rwro> <new pwd> <new pwd> | AP/SU | Specify new password (max 15 octs) | rw | |||
|
|
|
| rw=read/write password, ro=read only password |
|
|
ping <ip address> |
| AP/SU | Ping local Ethernet device | ro/rw | ||
|
|
|
| Note: This command only works for local Ethernet devices, not SU |
|
|
|
|
|
| or any device behind SU. |
|
|
power |
| AP/SU | Display current TX power level | ro/rw | ||
|
|
|
| default = max. power value |
|
|
power set <minmax<dBm> |
| AP/SU | Specify TX power for both band | rw | ||
|
|
|
| Note: SU’s power will be adjusted by AP during association process |
|
|
|
|
|
| (power leveling) |
|
|
|
|
|
|
|
|
|
| Trango Broadband Wireless — User Manual M2400S Rev. A |
| Page 40 | |||