Trango Broadband M2400S Standard External Power-over-Ethernet Junction Box, Integrated Antenna AP

Page 50

Type:	Linear wall mount transformer
Input:	120 VAC
Output:	20 VDC +/- 1 V
Max current:	600 mA
Connector:	5mm DC barrel-type plug
Standard External Power-over-Ethernet Junction Box
Type:	In-line female-to-female RJ-45 adapter for CAT-5 Ethernet cable
Connectors:
Eth. In:	Shielded RJ-45 Jack
DC Input:	5mm DC Barrel-type Jack
Eth. Out & DC Out:	Shielded RJ-45 Jack
Pinout for Eth. Out:	Power (+) on pins 7+8, ground (-) on pins 4+5, and eth. data on
	pins 1,2,3 & 6
Indicators:	2 LEDs to indicate power and a connection to radio
Protection:	Resettable fuse for DC input
Integrated Antenna AP
Type:	Air-loaded Patch Antenna
Polarization:	Vertical or Horizontal Polarization (electrically selectable)
Frequency:	2405 to 2475 MHz
Gain:	+13 +/- 1 dBiL
Az Beamwidth:	60 degrees (3 dB pts)
El Beamwidth:	18 degrees (3 dB pts)
Cross Pol:	>15 dB
Front/Back Ratio:	12 dB
VSWR:	< 2.0:1 over bandwidth
Integrated Antenna SU
Type:	Air-loaded Patch Antenna
Polarization:	Vertical or Horizontal Polarization (electrically selectable)
Frequency:	2405 to 2475 MHz
Gain:	+15 +/- 1 dBiL
Az Beamwidth:	32 degrees (3 dB pts)
El Beamwidth:	18 degrees (3 dB pts)
Cross Pol:	>15 dB
Front/Back Ratio:	12 dB
VSWR:	< 2.0:1 over bandwidth

Trango Broadband Wireless — User Manual M2400S Rev. A

Page 46

Image 50

Contents M2400S GHz Wireless Broadband System Table of Contents Table of Figures FCC Information Warranty Information Firmware NotificationsPreface CanadaIntroduction OverviewAuto-retransmit Feature ARQ SmartPolling & Bandwidth ThrottlingHardware Overview M2400S AP and SU Hardware ComponentsConnections and Power Getting StartedWiring Diagram Radio Management ConceptsBrowser Interface OpmodeBrowser Interface Login Primary Features and Pages of the Browser Interface Command Line Interface Telnet ip address of radioTroubleshooting This section you will Basic Configuration via Browser InterfaceConfiguring the AP Subscriber Unit Database Sudb Creating an SU in the Sudb CIR DownIP Address, Subnet Mask, and Gateway Configure Other Basic AP ParametersDefault Opmode Active Channel/PolarizationBasic Configuration via Browser Interface Configure Basic SU Parameters SU Basic SetupLED Summary Link ControlRF Link Loopback Test Advanced Setup SU Ranging TestOther Key Parameters Site Survey Set baseid baseid Basic Configuration via CLIAccess Point Basic Settings Ipconfig new ip new subnet mask new Set defaultopmode on or offSet defaultopmode on time sec Set apid apid 00-FF in HEXOn/off command Power set minmaxdBmSw 0 onoff default is on Sw 3 onoff default is offRemarks remarks Subscriber Unit Database SettingsSw 7 onoff default is on Sudb add suid prreg device id suid SU IDSubscriber Unit Basic Settings SU System Information Parameters and Related Commands Targetap apidSw 1 onoff Antenna h v eSw 0 onoff Sw 2 onoffMounting Hardware Part Number QTYInstallation Notes Cabling and Grounding ConsiderationsSite Selection Command survey time antennaDeployment AP Search and SU Antenna Alignment Site Survey ExampleRssi Command for Antenna Alignment AP SearchSu ping suid Link Management CommandsSU Alignment Using LEDs Su suid Su linktest suidSu testrflink suid Management ARQ with Selected Repeat and Multirate FeatureRadio Management Access Via TCP/IP SU Management from APSu ipconfig suid new ip new subnet new gateway Loading Multiple SU’s into Sudb using Dload CommandSu password suid all rw ro new password new password SU Bandwidth Monitoring Snmp SetupObjects for Monitoring and Control AP Bandwidth MonitoringManagement Appendix a Command Set Reference Command Radio Description AccessReboot unit Ro/rw Remarks Su ipconfig suid new IP new Default = Tftpd Receiver Specifications Appendix B SpecificationsRadio Transmit Specifications Mechanical and Environmental Specifications Ethernet I/O SpecificationsPower Specifications Standard External Power SupplyIntegrated Antenna SU Standard External Power-over-Ethernet Junction BoxIntegrated Antenna AP