Trango Broadband M2400S Mirth 0..3, Mbps, Freq ch# vh, Antenna vhe, Rfrxth, Power set minmaxdBm

Page 27

Basic Configuration via CLI

AP SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS

AP Parameter

Description

Related CLI Command

 

MIR Threshold (Kbps)

User specified MIR Threshold.

mirth [<0..3, Mbps>]

 

 

To specify total throughput

Example:

 

level that the AP will serve only

 

CIR (committed information

#>mirth 2

 

rate) to associated SUs.

 

 

 

When MIR Threshold is

 

 

 

disabled, the AP will serve MIR

 

 

 

for all its SUs.

 

 

 

When MIR Threshold is

 

 

 

activated, and the network

 

 

 

traffic exceeds the MIR

 

 

 

Threshold, the AP will only

 

 

 

serve CIR for all its SUs.

 

 

 

When MIR Threshold is

 

 

 

activated, and the network

 

 

 

traffic does NOT exceed the

 

 

 

MIR Threshold, the AP will

 

 

 

still serve MIR for all its SUs.

 

 

Active Channel

Current RF channel

freq [<ch#> <vh>]

 

 

 

Example:

 

 

#>freq 3

 

 

This command will change the channel of the AP to

 

 

3.

 

Antenna

Current antenna selection:

antenna [<vhe>]

 

 

(h)horizontal, (v)vertical,

 

 

 

(e)external

 

 

RF RX Threshold

Specifies the receiver

rfrxth <-90-85-80-75-70-65>

 

 

sensitivity of the AP. It is a

example:

 

powerful tool when the radio is

#>rfrxth –70

 

in a noisy environment. AP

 

 

 

will block out any signal

 

 

 

received which is below the RF

 

 

 

Rx threshold. Separate settings

 

 

 

exist for both ISM and UNII

 

 

 

bands.

 

 

RF TX Power

Current transmit power of the

power <set> <minmax<dBm>

 

 

AP not including antenna gain.

Example:

 

 

#>power set 10

Channel Table

Assigned frequencies to

freq writechannel [<ch#> <freq>]

 

 

channels. All channels may be

Example:

 

re-assigned as desired by the

#>freg writechannel 3 910

 

administrator.

This command will change channel 3 to 910 Mhz.

 

 

Broadcast Packet Filter

This software switch (0)

sw 0 [<onoff>] (default is on)

 

 

enables/disables the blocking of

Example:

 

Ethernet control packets, except

#>sw 0 on

 

ICMP and ARP, to reduce the

note: All switch settings (0-7) are set using the sw #

 

amount of unnecessary

 

overhead introduced to the

[<on/off>] command.

 

wireless link.

 

 

SU to SU

This software switch (3)

sw 3 [<onoff>] (default is off)

 

 

enables/disables the SU to SU

Example:

 

feature. When SU to SU is

#>sw 3 on

 

turned on, multiple SU’s within

 

 

 

 

 

 

Trango Broadband Wireless — User Manual M2400S Rev A

Page 23

Image 27
Contents M2400S GHz Wireless Broadband System Table of Contents Table of Figures Canada Warranty Information Firmware NotificationsPreface FCC InformationOverview IntroductionSmartPolling & Bandwidth Throttling Auto-retransmit Feature ARQM2400S AP and SU Hardware Components Hardware OverviewGetting Started Connections and PowerRadio Management Concepts Wiring DiagramOpmode Browser InterfaceBrowser Interface Login Primary Features and Pages of the Browser Interface Telnet ip address of radio Command Line InterfaceTroubleshooting Basic Configuration via Browser Interface Configuring the AP Subscriber Unit Database SudbThis section you will CIR Down Creating an SU in the SudbActive Channel/Polarization Configure Other Basic AP ParametersDefault Opmode IP Address, Subnet Mask, and GatewayBasic Configuration via Browser Interface SU Basic Setup Configure Basic SU ParametersLink Control LED SummaryRF Link Loopback Test SU Ranging Test Advanced SetupOther Key Parameters Site Survey Basic Configuration via CLI Access Point Basic SettingsSet baseid baseid Set apid apid 00-FF in HEX Set defaultopmode on or offSet defaultopmode on time sec Ipconfig new ip new subnet mask newSw 3 onoff default is off Power set minmaxdBmSw 0 onoff default is on On/off commandSudb add suid prreg device id suid SU ID Subscriber Unit Database SettingsSw 7 onoff default is on Remarks remarksSubscriber Unit Basic Settings Targetap apid SU System Information Parameters and Related CommandsSw 2 onoff Antenna h v eSw 0 onoff Sw 1 onoffPart Number QTY Mounting HardwareCabling and Grounding Considerations Installation NotesCommand survey time antenna DeploymentSite Selection Site Survey Example AP Search and SU Antenna AlignmentAP Search Rssi Command for Antenna AlignmentLink Management Commands SU Alignment Using LEDsSu ping suid Su linktest suid Su suidSu testrflink suid SU Management from AP ARQ with Selected Repeat and Multirate FeatureRadio Management Access Via TCP/IP ManagementLoading Multiple SU’s into Sudb using Dload Command Su password suid all rw ro new password new passwordSu ipconfig suid new ip new subnet new gateway AP Bandwidth Monitoring Snmp SetupObjects for Monitoring and Control SU Bandwidth MonitoringManagement Command Radio Description Access Appendix a Command Set ReferenceReboot unit Ro/rw Remarks Su ipconfig suid new IP new Default = Tftpd Appendix B Specifications Radio Transmit SpecificationsReceiver Specifications Standard External Power Supply Ethernet I/O SpecificationsPower Specifications Mechanical and Environmental SpecificationsStandard External Power-over-Ethernet Junction Box Integrated Antenna APIntegrated Antenna SU