Trango Broadband M2400S user manual Default = Tftpd

Page 47

Command	Radio	Description		Access
		default = -60
tftpd	AP/SU	display current TFTPD status (status is either on or off) This		ro/rw
		command will also list any contents of the TFTP buffer.
tftpd <on off>	AP/SU	enable or disable TFTPD service. TFTPD must be on in order to		rw
		upload new firmware or new SUDB file.
updateflash <systemsetting ss>	AP/SU	Save current settings. This command can be issued in several ways:		rw
		save ss, updateflash systemsetting, save systemsetting, and
		updateflash ss
updateflash <mainimage fpgaimage>	AP/SU	Retrieve uploaded firmware from TFTP buffer, verify checksum,		rw
<current chscksum> <new checksum>		and write to flash memory at main or FPGA image section.

updateflash sudb	AP	Save SUDB into flash memory		rw
ver	AP/SU	Display firmware and date codes		ro/rw
		1.	Version number and date code
		2.	Firmware and FPGA version code
		3.	Firmware and FPGA image checksum

Trango Broadband Wireless — User Manual M2400S Rev. A

Page 43

Image 47

Contents M2400S GHz Wireless Broadband System Table of Contents Table of Figures Canada Warranty Information Firmware NotificationsPreface FCC InformationOverview IntroductionSmartPolling & Bandwidth Throttling Auto-retransmit Feature ARQM2400S AP and SU Hardware Components Hardware OverviewGetting Started Connections and PowerRadio Management Concepts Wiring DiagramOpmode Browser InterfaceBrowser Interface Login Primary Features and Pages of the Browser Interface Telnet ip address of radio Command Line InterfaceTroubleshooting This section you will Basic Configuration via Browser InterfaceConfiguring the AP Subscriber Unit Database Sudb CIR Down Creating an SU in the SudbActive Channel/Polarization Configure Other Basic AP ParametersDefault Opmode IP Address, Subnet Mask, and GatewayBasic Configuration via Browser Interface SU Basic Setup Configure Basic SU ParametersLink Control LED SummaryRF Link Loopback Test SU Ranging Test Advanced SetupOther Key Parameters Site Survey Set baseid baseid Basic Configuration via CLIAccess Point Basic Settings Set apid apid 00-FF in HEX Set defaultopmode on or offSet defaultopmode on time sec Ipconfig new ip new subnet mask newSw 3 onoff default is off Power set minmaxdBmSw 0 onoff default is on On/off commandSudb add suid prreg device id suid SU ID Subscriber Unit Database SettingsSw 7 onoff default is on Remarks remarksSubscriber Unit Basic Settings Targetap apid SU System Information Parameters and Related CommandsSw 2 onoff Antenna h v eSw 0 onoff Sw 1 onoffPart Number QTY Mounting HardwareCabling and Grounding Considerations Installation NotesSite Selection Command survey time antennaDeployment Site Survey Example AP Search and SU Antenna AlignmentAP Search Rssi Command for Antenna AlignmentSu ping suid Link Management CommandsSU Alignment Using LEDs Su linktest suid Su suidSu testrflink suid SU Management from AP ARQ with Selected Repeat and Multirate FeatureRadio Management Access Via TCP/IP ManagementSu ipconfig suid new ip new subnet new gateway Loading Multiple SU’s into Sudb using Dload CommandSu password suid all rw ro new password new password AP Bandwidth Monitoring Snmp SetupObjects for Monitoring and Control SU Bandwidth MonitoringManagement Command Radio Description Access Appendix a Command Set ReferenceReboot unit Ro/rw Remarks Su ipconfig suid new IP new Default = Tftpd Receiver Specifications Appendix B SpecificationsRadio Transmit Specifications Standard External Power Supply Ethernet I/O SpecificationsPower Specifications Mechanical and Environmental SpecificationsIntegrated Antenna SU Standard External Power-over-Ethernet Junction BoxIntegrated Antenna AP