Trango Broadband M2400S Set apid apid 00-FF in HEX, Opmode on y, Set defaultopmode on or off

Page 26

Basic Configuration via CLI

	AP SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS
AP Parameter		Description	Related CLI Command
AP ID		This parameter provides a	set apid <apid> (00-FF in HEX)
		unique number for each AP. If
		Target AP is specified on SU,	Example:
		the SU can only authenticate	#>set apid 33
		with the specified AP. The
		default AP ID is the last two
		bytes of the MAC address.
Opmode		Current Opmode of the radio.	opmode on y
			This sets the radio to Opmode “ON.” If the radio is
			accessed via the Ethernet port within the first 30
			seconds after reboot/power cycle, the Opmode will
			default to “OFF.”
Default Opmode		Determines the Opmode (“ON”	set defaultopmode <on or off>
		or “OFF”) of the radio after	Example:
		reboot/power cycle. When this	Example:
		parameter is set to “ON,” the	#>set defaultopmode on
		radio will progress into
		Opmode “ON” automatically
		after a reboot/power cycle.
Opmode Start		Determines the amount of time	set defaultopmode on [<time (sec)>]
		the radio will remain in	Example:
		Opmode “OFF” after	Example:
		reboot/power cycle before	#>set defaultopmode on 60
		progressing to the default
		Opmode.
IP		IP, Subnet, and Gateway	ipconfig [<new ip> <new subnet mask> <new
Subnet		address of the radio.	gateway>]
Gateway			Example:
			Example:
			#>ipconfig 10.1.1.2 255.0.0.0 10.1.1.1
TFTPD Status		TFTPD status (on or off).	tftpd [<onoff>]
		TFTPD should be turned on to	Example:
		import a file into the radio	#>tftpd on
		(such as new firmware).
		Default is off. TFTPD will
		revert to Off after rebooting.

Trango Broadband Wireless — User Manual M2400S Rev A

Page 22

Image 26

Contents M2400S GHz Wireless Broadband System Table of Contents Table of Figures FCC Information Warranty Information Firmware NotificationsPreface CanadaIntroduction OverviewAuto-retransmit Feature ARQ SmartPolling & Bandwidth ThrottlingHardware Overview M2400S AP and SU Hardware ComponentsConnections and Power Getting StartedWiring Diagram Radio Management ConceptsBrowser Interface OpmodeBrowser Interface Login Primary Features and Pages of the Browser Interface Command Line Interface Telnet ip address of radioTroubleshooting This section you will Basic Configuration via Browser InterfaceConfiguring the AP Subscriber Unit Database Sudb Creating an SU in the Sudb CIR DownIP Address, Subnet Mask, and Gateway Configure Other Basic AP ParametersDefault Opmode Active Channel/PolarizationBasic Configuration via Browser Interface Configure Basic SU Parameters SU Basic SetupLED Summary Link ControlRF Link Loopback Test Advanced Setup SU Ranging TestOther Key Parameters Site Survey Set baseid baseid Basic Configuration via CLIAccess Point Basic Settings Ipconfig new ip new subnet mask new Set defaultopmode on or offSet defaultopmode on time sec Set apid apid 00-FF in HEXOn/off command Power set minmaxdBmSw 0 onoff default is on Sw 3 onoff default is offRemarks remarks Subscriber Unit Database SettingsSw 7 onoff default is on Sudb add suid prreg device id suid SU IDSubscriber Unit Basic Settings SU System Information Parameters and Related Commands Targetap apidSw 1 onoff Antenna h v eSw 0 onoff Sw 2 onoffMounting Hardware Part Number QTYInstallation Notes Cabling and Grounding ConsiderationsSite Selection Command survey time antennaDeployment AP Search and SU Antenna Alignment Site Survey ExampleRssi Command for Antenna Alignment AP SearchSu ping suid Link Management CommandsSU Alignment Using LEDs Su suid Su linktest suidSu testrflink suid Management ARQ with Selected Repeat and Multirate FeatureRadio Management Access Via TCP/IP SU Management from APSu ipconfig suid new ip new subnet new gateway Loading Multiple SU’s into Sudb using Dload CommandSu password suid all rw ro new password new password SU Bandwidth Monitoring Snmp SetupObjects for Monitoring and Control AP Bandwidth MonitoringManagement Appendix a Command Set Reference Command Radio Description AccessReboot unit Ro/rw Remarks Su ipconfig suid new IP new Default = Tftpd Receiver Specifications Appendix B SpecificationsRadio Transmit Specifications Mechanical and Environmental Specifications Ethernet I/O SpecificationsPower Specifications Standard External Power SupplyIntegrated Antenna SU Standard External Power-over-Ethernet Junction BoxIntegrated Antenna AP