Trango Broadband M2400S Preface, FCC Information, Warranty Information Firmware Notifications

Page 4

Preface

Preface

This manual covers basic configuration and installation of the M2400S Wireless Broadband System and applies to the following radio part numbers:

M2400S-AP

2.4 GHz Access Point

M2400S-SU

2.4 GHz Subscriber Unit

FCC Information

This device complies with Part 15 of FCC Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and radiates radio-frequency energy; if not installed and used in accordance with these instructions, the unit may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in any particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one or more of the following measures:

1)Reorient the antenna.

2)Increase the separation between the affected equipment and the unit.

3)Connect the affected equipment to a power outlet on a different circuit from the one the receiver is connected to.

4)Consult the dealer and/or experienced radio/TV technician for help.

FCC ID: NCYM2400S

Canada:

IMPORTANT NOTE: Intentional or unintentional changes or modifications must not be made unless under the express consent of the party responsible for compliance. Any such modifications could void the user’s authority to operate the equipment and will void the manufacturer’s warranty. To comply with FCC RF exposure requirements, the following antenna installation and device operating configurations must be satisfied. The antenna for this unit must be fixed and mounted on an outdoor permanent structure with a minimum separation distance of two meters from any persons. Furthermore, it must not be co-located or operated in conjunction with any other antenna or transmitter.

Warranty Information

Radios from Trango Broadband Wireless are warranted for one year from date of purchase. Please see www.trangobroadband.com for a complete description of warranty coverage and limitations.

Firmware Notifications

To receive email notifications regarding firmware upgrades and product announcements, register at http://www.trangobroadband.com/mailinglist/mailingListAdd.aspx

Trango Broadband Wireless — M2400S User Manual Rev A

page iv

Image 4
Contents M2400S GHz Wireless Broadband System Table of Contents Table of Figures Warranty Information Firmware Notifications PrefaceFCC Information CanadaIntroduction OverviewAuto-retransmit Feature ARQ SmartPolling & Bandwidth ThrottlingHardware Overview M2400S AP and SU Hardware ComponentsConnections and Power Getting StartedWiring Diagram Radio Management ConceptsBrowser Interface OpmodeBrowser Interface Login Primary Features and Pages of the Browser Interface Command Line Interface Telnet ip address of radioTroubleshooting Configuring the AP Subscriber Unit Database Sudb Basic Configuration via Browser InterfaceThis section you will Creating an SU in the Sudb CIR DownConfigure Other Basic AP Parameters Default OpmodeIP Address, Subnet Mask, and Gateway Active Channel/PolarizationBasic Configuration via Browser Interface Configure Basic SU Parameters SU Basic SetupLED Summary Link ControlRF Link Loopback Test Advanced Setup SU Ranging TestOther Key Parameters Site Survey Access Point Basic Settings Basic Configuration via CLISet baseid baseid Set defaultopmode on or off Set defaultopmode on time secIpconfig new ip new subnet mask new Set apid apid 00-FF in HEXPower set minmaxdBm Sw 0 onoff default is onOn/off command Sw 3 onoff default is offSubscriber Unit Database Settings Sw 7 onoff default is onRemarks remarks Sudb add suid prreg device id suid SU IDSubscriber Unit Basic Settings SU System Information Parameters and Related Commands Targetap apidAntenna h v e Sw 0 onoffSw 1 onoff Sw 2 onoffMounting Hardware Part Number QTYInstallation Notes Cabling and Grounding ConsiderationsDeployment Command survey time antennaSite Selection AP Search and SU Antenna Alignment Site Survey ExampleRssi Command for Antenna Alignment AP SearchSU Alignment Using LEDs Link Management CommandsSu ping suid Su suid Su linktest suidSu testrflink suid ARQ with Selected Repeat and Multirate Feature Radio Management Access Via TCP/IPManagement SU Management from APSu password suid all rw ro new password new password Loading Multiple SU’s into Sudb using Dload CommandSu ipconfig suid new ip new subnet new gateway Snmp Setup Objects for Monitoring and ControlSU Bandwidth Monitoring AP Bandwidth MonitoringManagement Appendix a Command Set Reference Command Radio Description AccessReboot unit Ro/rw Remarks Su ipconfig suid new IP new Default = Tftpd Radio Transmit Specifications Appendix B SpecificationsReceiver Specifications Ethernet I/O Specifications Power SpecificationsMechanical and Environmental Specifications Standard External Power SupplyIntegrated Antenna AP Standard External Power-over-Ethernet Junction BoxIntegrated Antenna SU