Trango Broadband M2400S user manual Su suid, Su linktest suid

Page 38

Deployment

[001]

Ping #0 -> -52 dB 220 us 0.0 mi Ping #1 -> -53 dB 219 us 0.0 mi Ping #2 -> -53 dB 220 us 0.0 mi Ping #3 -> -52 dB 220 us 0.0 mi Ping #4 -> -53 dB 219 us 0.0 mi Ping #5 -> -52 dB 220 us 0.0 mi Ping #6 -> -50 dB 220 us 0.0 mi Ping #7 -> -52 dB 220 us 0.0 mi Ping #8 -> -52 dB 220 us 0.0 mi Ping #9 -> -52 dB 220 us 0.0 mi [#End]

Avg = -51 dB Success.

su <suid>

AP will poll the SU for SU’s current status and will provide information such as SU range from AP, signal strength received at SU from AP, SU temperature, etc.

Example: #> su 1

[ 1] pr [as] y [d] 0.0 [rssi at ap] -50 dBm [rssi at su] -60 dBm

[ip] 10.8.1.234 [subnet] 255.255.255.192 [gateway] 10.8.1.193 [mac] 00 01 DE 19 F0 A4

[hw ver] 0006 [fpga ver] 04042201 [fpga chksum] 47231EEE [fw ver] 1p0x8 [fw chksum] 6DDF232C [fw datecode] 04061502 [default channel and antenna] 1 h [active channel and antenna] 1 h [tx power] 23 dBm

[ch#1] 2405 [ch#2] 2415 [ch#3] 2425 [ch#4] 2435 [ch#5] 2445 [ch#6] 2455 [ch#7] 2465 [ch#8] 2475

[remarks]

[RF Tx Retry at AP] 0 [RF Tx Retry Maxed Out at AP] 0

[RF Tx Retry at SU] 0 [RF Tx Retry Maxed Out at SU] 0 Success.

#>

su linktest <suid>

This command checks the integrity of the wireless link from the standpoint of performance (throughput) and over-the-air packet loss. The AP will send 100 1600 byte packets to the SU, and the SU will return the packets it receives to the AP. A perfect link (without dropped packets) will yield average throughput of 5,000 Kbps. If heavy packet loss occurs it may be caused by interference or multi-path.

Example:

#> su linktest 1

[suid] 1 [pkt len] 1600 bytes [# of pkts per cycle] 100 [cycle] 10

0[AP Tx] 100 [AP Rx] 100 [AP RxErr] 0 [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0 5

00 ms 5120 kbps

1 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0 [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0 5 00 ms 5120 kbps

2 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0 [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0 5 00 ms 5120 kbps

3 [AP Tx] 100 [AP Rx] 100 [AP RxErr] 0 [SU Tx] 100 [SU Rx] 100 [SU RxErr] 0 5 00 ms 5120 kbps

Trango Broadband Wireless — User Manual M2400S Rev A

Page 34

Image 38

Contents M2400S GHz Wireless Broadband System Table of Contents Table of Figures FCC Information Warranty Information Firmware NotificationsPreface CanadaIntroduction OverviewAuto-retransmit Feature ARQ SmartPolling & Bandwidth ThrottlingHardware Overview M2400S AP and SU Hardware ComponentsConnections and Power Getting StartedWiring Diagram Radio Management ConceptsBrowser Interface OpmodeBrowser Interface Login Primary Features and Pages of the Browser Interface Command Line Interface Telnet ip address of radioTroubleshooting This section you will Basic Configuration via Browser InterfaceConfiguring the AP Subscriber Unit Database Sudb Creating an SU in the Sudb CIR DownIP Address, Subnet Mask, and Gateway Configure Other Basic AP ParametersDefault Opmode Active Channel/PolarizationBasic Configuration via Browser Interface Configure Basic SU Parameters SU Basic SetupLED Summary Link ControlRF Link Loopback Test Advanced Setup SU Ranging TestOther Key Parameters Site Survey Set baseid baseid Basic Configuration via CLIAccess Point Basic Settings Ipconfig new ip new subnet mask new Set defaultopmode on or offSet defaultopmode on time sec Set apid apid 00-FF in HEXOn/off command Power set minmaxdBmSw 0 onoff default is on Sw 3 onoff default is offRemarks remarks Subscriber Unit Database SettingsSw 7 onoff default is on Sudb add suid prreg device id suid SU IDSubscriber Unit Basic Settings SU System Information Parameters and Related Commands Targetap apidSw 1 onoff Antenna h v eSw 0 onoff Sw 2 onoffMounting Hardware Part Number QTYInstallation Notes Cabling and Grounding ConsiderationsSite Selection Command survey time antennaDeployment AP Search and SU Antenna Alignment Site Survey ExampleRssi Command for Antenna Alignment AP SearchSu ping suid Link Management CommandsSU Alignment Using LEDs Su suid Su linktest suidSu testrflink suid Management ARQ with Selected Repeat and Multirate FeatureRadio Management Access Via TCP/IP SU Management from APSu ipconfig suid new ip new subnet new gateway Loading Multiple SU’s into Sudb using Dload CommandSu password suid all rw ro new password new password SU Bandwidth Monitoring Snmp SetupObjects for Monitoring and Control AP Bandwidth MonitoringManagement Appendix a Command Set Reference Command Radio Description AccessReboot unit Ro/rw Remarks Su ipconfig suid new IP new Default = Tftpd Receiver Specifications Appendix B SpecificationsRadio Transmit Specifications Mechanical and Environmental Specifications Ethernet I/O SpecificationsPower Specifications Standard External Power SupplyIntegrated Antenna SU Standard External Power-over-Ethernet Junction BoxIntegrated Antenna AP