Trango Broadband M2400S user manual Loading Multiple SU’s into Sudb using Dload Command

Page 41

Management

You can remotely change the SUs password for a single SU or all SUs in a sector using the syntax below:

su password <suid all> <rw ro> <new password> <new password>

Example: su password all rw hello hello

To remotely change the read write password on all SUs to “hello.”

You can change the SUs IP, subnet, and gateway using the syntax below:

su ipconfig <suid> <new ip> <new subnet> <new gateway>

Example:

su ipconfig 7 192.168.10.10 255.255.255.0 192.168.10.1

In this example SU ID 7’s IP address was changed to 192.168.10.10, the subnet mask to 255.255.255.0, and the gateway to 192.168.10.1.

A complete description of these commands and many others can be found in Appendix A − Command Set Summary.

Loading Multiple SU’s into SUDB using DLOAD Command

To load a full database of SU entries into the AP’s SUDB, you will need to create an SUDB in ASCII text file format. As shown below, each row represents all information for one SU. Each column is an information field, which includes: SU ID, SU to SU group, service level, CIR, MIR, and MAC address.

005

re a

1

3000

3000

3000

3000 0000 00 01 de 16 e3 60

--- Subscriber 1

007

re a

1

3000

3000

3000

3000 0000 00 01 de 16 e3 7c

--- Subscriber 2

009

re a

1

3000

3000

3000

3000 0000 00 01 de 16 e3 7b

--- Subscriber 3

000

-- -

- ----

----

----

----

 

--- End of file indicator

---

---- -----------------

 

 

MAC Address

-----------------

 

 

 

Reserved (should be 0000)

 

-----------------------

 

 

 

 

 

mir uplink

----------------------------

 

 

 

 

 

 

 

 

mir downlink

---------------------------------

 

 

 

 

 

 

 

 

 

 

 

cir uplink

--------------------------------------

 

 

 

 

 

 

 

 

 

 

 

 

 

 

cir downlink

-------------------------------------------

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

su2su group id

 

----------------------------------------------

 

 

 

 

 

 

 

 

 

 

 

 

-------------------------------------------------

 

 

 

 

 

rate (currently not supported,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

value should be a)

----------------------------------------------------

 

 

 

 

 

 

pr priority/regular user

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-------------------------------------------------------

 

 

 

 

 

 

 

 

su id (1..127)

 

 

 

 

 

 

 

 

 

 

1.Telnet into the AP, and run the command tftpd on to enable tftp process.

Trango Broadband Wireless — User Manual M2400S Rev A

Page 37

Image 41
Contents M2400S GHz Wireless Broadband System Table of Contents Table of Figures Preface Warranty Information Firmware NotificationsFCC Information CanadaOverview IntroductionSmartPolling & Bandwidth Throttling Auto-retransmit Feature ARQM2400S AP and SU Hardware Components Hardware OverviewGetting Started Connections and PowerRadio Management Concepts Wiring DiagramOpmode Browser InterfaceBrowser Interface Login Primary Features and Pages of the Browser Interface Telnet ip address of radio Command Line InterfaceTroubleshooting This section you will Basic Configuration via Browser InterfaceConfiguring the AP Subscriber Unit Database Sudb CIR Down Creating an SU in the SudbDefault Opmode Configure Other Basic AP ParametersIP Address, Subnet Mask, and Gateway Active Channel/PolarizationBasic Configuration via Browser Interface SU Basic Setup Configure Basic SU ParametersLink Control LED SummaryRF Link Loopback Test SU Ranging Test Advanced SetupOther Key Parameters Site Survey Set baseid baseid Basic Configuration via CLIAccess Point Basic Settings Set defaultopmode on time sec Set defaultopmode on or offIpconfig new ip new subnet mask new Set apid apid 00-FF in HEXSw 0 onoff default is on Power set minmaxdBmOn/off command Sw 3 onoff default is offSw 7 onoff default is on Subscriber Unit Database SettingsRemarks remarks Sudb add suid prreg device id suid SU IDSubscriber Unit Basic Settings Targetap apid SU System Information Parameters and Related CommandsSw 0 onoff Antenna h v eSw 1 onoff Sw 2 onoffPart Number QTY Mounting HardwareCabling and Grounding Considerations Installation NotesSite Selection Command survey time antennaDeployment Site Survey Example AP Search and SU Antenna AlignmentAP Search Rssi Command for Antenna AlignmentSu ping suid Link Management CommandsSU Alignment Using LEDs Su linktest suid Su suidSu testrflink suid Radio Management Access Via TCP/IP ARQ with Selected Repeat and Multirate FeatureManagement SU Management from APSu ipconfig suid new ip new subnet new gateway Loading Multiple SU’s into Sudb using Dload CommandSu password suid all rw ro new password new password Objects for Monitoring and Control Snmp SetupSU Bandwidth Monitoring AP Bandwidth MonitoringManagement Command Radio Description Access Appendix a Command Set ReferenceReboot unit Ro/rw Remarks Su ipconfig suid new IP new Default = Tftpd Receiver Specifications Appendix B SpecificationsRadio Transmit Specifications Power Specifications Ethernet I/O SpecificationsMechanical and Environmental Specifications Standard External Power SupplyIntegrated Antenna SU Standard External Power-over-Ethernet Junction BoxIntegrated Antenna AP