Tandberg Data Tandberg LTO2 manual FCC Class B Notice, Trademarks

Page 2

Trademarks

Linear Tape-Open, LTO and Ultrium are trademarks of Hewlett-Packard, IBM Corporation and Seagate Technology.

Microsoft, Windows, Windows NT, and its logo are registered trademarks of Microsoft Corporation in the United States and other countries.

Other brands and product names appearing herein may be trademarks or registered trademarks of their respective owners.

FCC Class B Notice

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

1.This device may not cause harmful interference.

2.This device must accept any interference received, including interference that may cause undesired operation.

Note:

This equipment has been tested and founded to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful Interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

･Reorient or relocate the receiving antenna

･Increase the separation between the equipment and receiver

･Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

･Consult the dealer or an experienced radio / television technician for help.

CAUTIONS:

(1)All rights reserved.

(2)The contents of this document may be changed without prior notice.

(3)No part of this document may be reproduced without the permission of Tandberg.

(4)Though the contents of this manual are thoroughly prepared, please contact the dealer you purchased if you have any questions, or if mistakes or omissions are found.

(5)Tandberg shall not be held liable for the effect of operations, regardless of item (4).

Image 2

Contents Tandberg LTO2 Autoloader FCC Class B Notice TrademarksSafety Descriptions Description example in this manualProhibited action Mandatory actionSafety Cautions General CautionsDo not apply starburst wiring Do not cover the air inlet Do not lift the device aloneDo not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Cartridges Chapter Daily MaintenanceChapter Troubleshooting Introduction Organization of this manual Tip Symbols used in this manualSymbols used in this manual Tandberg LTO2 Autoloader Overview of the Tandberg LTO2 AutoloaderNames and Functions of the Parts Front Panel of the Tandberg LTO2 Autoloader･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display Liquid Crystal Display LCDMain Unit Handling PrecautionsTransfer or Disposal of the Device CartridgesContents of the Carton Transporter Locking Screw Instruction TAG SetupPreparation Before Use Scsi Cable Connections Storing the Transporter Locking Screw for later useAC Power Cable Connection AC Power Cable ConnectionAttaching and removing the Filter Element Attaching and removing a Filter ElementSwitching on the Power Switch and the Power-On Sequence Scsi ID SettingStart and Shutdown of the System Operation Removal of the MagazineLoading the Magazine Loading the MagazineLoading the Cartridge Loading to MagazineOperation Examples For using the Tandberg LTO2 Autoloader w/BCRs optionalLoading to the Fixed Slots For using the Tandberg LTO2 Autoloader w/BCR Removal and Insertion of the Cartridges Removal from and Insertion to the MagazineRemoval from and Insertion to the Fixed Slots Display Eject Slot?Operation of the Panel Keys Organization of the Front Panel SwitchesFunctions of the Switches Slot Logical NumbersPanel Operation Procedure Display Frm Slt 1? Menu Commands Menu Tree 1 Main MenuRetry Mode Setting the Scsi ID Checking the Scsi IDChanging the Scsi ID Operation ExampleTip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release KeyCartridges CartridgesCleaning Cartridge Data CartridgeWrite-Protect Switch Setting the Write-protect SwitchUsing Bar Code Labels Precautions Bar Code LabelUsage Precautions General PrecautionsStorage of Data Cartridges Service LifeStandards for Prohibition of Use Cleaning of the Drive Head Daily MaintenanceCleaning Manually Cleaning of the Drive Head Checking the CLNROL- function Cleaning the Roller inside of the transporterDefault CLNROL-function setting Enable Setting the CLNROL- function Disable Operation Example Changing the RtyCnt valueRtyCnt value in the CLNROL-function Tip Cleaning of the Roller Execution timing of the cleaningTools and Parts Setting Maintenance mode Setting Cleaning mode Cleaning the RollerShows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the fixed slots Cleaning of the Main UnitCleaning of the exterior Cleaning of the interiorCleaning of the magazine Cleaning of the cartridgeMovement and Shipping of the Autoloader Troubleshooting Phenomenon Recovery Procedure Power SupplyPhenomenon Recovery Procedure Cartridge Operation ConnectionsOthers Phenomenon Recovery Procedure Autoloader PerformanceCleaning Recovery Procedure P move system initialization Exceeding the recommended operation When Requesting Maintenance Other Matters to CheckAppendix a Specifications Autoloader Main UnitUniversal cleaning cartridge TD P/N LTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/NSupplies Appendix B Optional Items and SuppliesOptional Items Appendix C Error Code CMer Error CodeErr ×××× Messages Messages Related to the Drive InterfacePanel Operation and Other Messages Message DescriptionTandberg LTO2 Autoloader Installation and User’s Manual Tandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway