Tandberg Data Tandberg LTO2 manual Err

Page 81

CMer Error Code 2

Table-D2 sorts the contents of CMer error code 2 errors.

Displayed here is a further classification of the operation of CMer error code 1.

Table-D2 CMer Error Code 2 Table

□□

Description

00This error code is conforms to the upper "CMer Error Code 1".

20An error occurring during ejection of the cartridge from the drive.

30An error occurring during loading of the cartridge to the drive.

40An error occurring during transporter P drive system initialization-error restoration.

50An error occurring during ejection of the cartridge from the magazine slot.

60An error occurring during loading of the cartridge to the magazine slot.

70An error occurring during transporter Y move.

80An error occurring during inventory check of the cartridges.

81An error occurring during reading the bar code label.

9X	An error occurring during accessing the drive.

CMer Error Code 3

These error codes show an essential factor of CMer error.See Capter6(code with cause and Recovery Procedure).

D.err

The displayed error codes are 4 digits and configured as described below.

Examples of error code displays		:	D.err ○○○○
Table-D4 sorts the D.err error codes and their contents.
	Table-D4		D.err Error Code Table

○○○○			Description

0101	The Autoloader detected timeout error on the communication with the drive.
0110	The Autoloader detected parity error on the communication with the drive.
0111	The Autoloader detected framing error on the communication with the drive.
0112	The Autoloader detected overrun error on the communication with the drive.
0140	The Autoloader detected an error on the Load/Unload command.
0170	The Autoloader detected an error on the communication with the drive.
0180	The Autoloader detected an error on the communication with the drive.(NAK retry over)
0181	The Autoloader detected an error on the communication with the drive.(SNAK retry over)
0102～010F,	The Autoloader detected cartridge position or timeout error before issuing
0113～013F	Load/Unload/Unthread command.
0190	The Autoloader detected timeout error before issuing Unload command.
0191	The Autoloader detected timeout error before finishing Unload command.
0192	The Autoloader detected state error on the communication with the drive .

- 65 -

Image 81

Contents Tandberg LTO2 Autoloader Trademarks FCC Class B NoticeDescription example in this manual Safety DescriptionsMandatory action Prohibited actionGeneral Cautions Safety CautionsDo not apply starburst wiring Do not lift the device alone Do not cover the air inletDo not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Daily Maintenance Chapter TroubleshootingChapter Cartridges Introduction Organization of this manual Symbols used in this manual Symbols used in this manualTip Overview of the Tandberg LTO2 Autoloader Tandberg LTO2 AutoloaderFront Panel of the Tandberg LTO2 Autoloader Names and Functions of the Parts･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display LCD Liquid Crystal DisplayTransfer or Disposal of the Device Handling PrecautionsMain Unit CartridgesContents of the Carton Setup Preparation Before UseTransporter Locking Screw Instruction TAG Storing the Transporter Locking Screw for later use Scsi Cable ConnectionsAC Power Cable Connection AC Power Cable ConnectionAttaching and removing a Filter Element Attaching and removing the Filter ElementScsi ID Setting Switching on the Power Switch and the Power-On SequenceStart and Shutdown of the System Removal of the Magazine OperationLoading the Magazine Loading the MagazineLoading to Magazine Loading the CartridgeFor using the Tandberg LTO2 Autoloader w/BCRs optional Loading to the Fixed SlotsOperation Examples For using the Tandberg LTO2 Autoloader w/BCR Removal from and Insertion to the Magazine Removal and Insertion of the CartridgesDisplay Eject Slot? Removal from and Insertion to the Fixed SlotsFunctions of the Switches Organization of the Front Panel SwitchesOperation of the Panel Keys Slot Logical NumbersPanel Operation Procedure Display Frm Slt 1? Menu Tree 1 Main Menu Menu CommandsRetry Mode Checking the Scsi ID Setting the Scsi IDOperation Example Changing the Scsi IDTip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release KeyCartridges CartridgesData Cartridge Cleaning CartridgeSetting the Write-protect Switch Write-Protect SwitchBar Code Label Using Bar Code Labels PrecautionsGeneral Precautions Usage PrecautionsService Life Standards for Prohibition of UseStorage of Data Cartridges Daily Maintenance CleaningCleaning of the Drive Head Manually Cleaning of the Drive Head Cleaning the Roller inside of the transporter Default CLNROL-function setting EnableChecking the CLNROL- function Setting the CLNROL- function Disable Changing the RtyCnt value RtyCnt value in the CLNROL-functionOperation Example Tip Execution timing of the cleaning Cleaning of the RollerTools and Parts Setting Maintenance mode Cleaning the Roller Setting Cleaning modeShows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the exterior Cleaning of the Main UnitCleaning of the fixed slots Cleaning of the interiorCleaning of the cartridge Cleaning of the magazineMovement and Shipping of the Autoloader Phenomenon Recovery Procedure Power Supply TroubleshootingConnections Phenomenon Recovery Procedure Cartridge OperationPhenomenon Recovery Procedure Autoloader Performance CleaningOthers Recovery Procedure P move system initialization Exceeding the recommended operation Other Matters to Check When Requesting MaintenanceAutoloader Main Unit Appendix a SpecificationsLTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/N Universal cleaning cartridge TD P/NAppendix B Optional Items and Supplies Optional ItemsSupplies CMer Error Code Appendix C Error CodeErr ×××× Messages Related to the Drive Interface MessagesMessage Description Panel Operation and Other MessagesTandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway Tandberg LTO2 Autoloader Installation and User’s Manual