Tandberg Data Tandberg LTO2 manual Phenomenon Recovery Procedure Cartridge Operation, Connections

Page 71

Phenomenon

Recovery Procedure

 

 

Cartridge Operation

 

 

 

Cartridge is entwined in the

･Execute cleaning of the Roller.See”Section 5.1.2”

･If the phenomenon has a relapse,contact your nearest Customer Support

transporter.

Center.

 

 

 

Transporter does not

･Execute cleaning of the Roller.See”Section 5.1.2”

･If the phenomenon has a relapse,contact your nearest Customer Support

load/unload the cartridge.

Center.

 

 

 

The cartridge could not be taken

･Execute cleaning of the Roller.See”Section 5.1.2”

･If the phenomenon has a relapse,contact your nearest Customer Support

out from the drive.

Center.

 

 

 

Connections

 

 

 

Host does not detect

･Check whether the terminating connector is mounted to the Autoloader

and whether the cables are properly connected.

Autoloader.

･Check whether the Autoloader is recognized by the operating system.

 

 

 

 

･When the backup software detects the drive but does not detect the

 

Autoloader, check whether the Autoloader module or the changer option

Backup software application of

accompanies the backup software. Most software packages require an

the host does not detect

Autoloader "robotic" and an additional module for communications.

Autoloader.

･When the backup software detects the Autoloader but does not detect the

 

drive, check whether the correct backup software driver has been

 

installed.

 

 

Changed SCSI ID of the drive is

･Check whether different ID numbers have been assigned to the SCSI

not recognized by the host

devices on the same bus.

computer.

･Restart the host.

 

 

After connection to the

･Check that there are no conflicts of the SCSI ID among all the devices

Autoloader, the response speed

connected to the host.

slows down, or the system

･There is no need to put the SCSI ID in a specific order on the backup

stops.

software.

 

 

- 55 -

Page 70 Page 72
Image 71
Page 70 Page 72
Contents Tandberg LTO2 Autoloader Trademarks FCC Class B NoticeDescription example in this manual Safety DescriptionsMandatory action Prohibited actionGeneral Cautions Safety CautionsDo not apply starburst wiring Do not lift the device alone Do not cover the air inletDo not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Cartridges Chapter Daily MaintenanceChapter Troubleshooting Introduction Organization of this manual Tip Symbols used in this manualSymbols used in this manual Overview of the Tandberg LTO2 Autoloader Tandberg LTO2 AutoloaderFront Panel of the Tandberg LTO2 Autoloader Names and Functions of the Parts･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display LCD Liquid Crystal DisplayCartridges Handling PrecautionsTransfer or Disposal of the Device Main UnitContents of the Carton Transporter Locking Screw Instruction TAG SetupPreparation Before Use Storing the Transporter Locking Screw for later use Scsi Cable ConnectionsAC Power Cable Connection AC Power Cable ConnectionAttaching and removing a Filter Element Attaching and removing the Filter ElementScsi ID Setting Switching on the Power Switch and the Power-On SequenceStart and Shutdown of the System Removal of the Magazine OperationLoading the Magazine Loading the MagazineLoading to Magazine Loading the CartridgeOperation Examples For using the Tandberg LTO2 Autoloader w/BCRs optionalLoading to the Fixed Slots For using the Tandberg LTO2 Autoloader w/BCR Removal from and Insertion to the Magazine Removal and Insertion of the CartridgesDisplay Eject Slot? Removal from and Insertion to the Fixed SlotsSlot Logical Numbers Organization of the Front Panel SwitchesFunctions of the Switches Operation of the Panel KeysPanel Operation Procedure Display Frm Slt 1? Menu Tree 1 Main Menu Menu CommandsRetry Mode Checking the Scsi ID Setting the Scsi IDOperation Example Changing the Scsi IDTip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release KeyCartridges CartridgesData Cartridge Cleaning CartridgeSetting the Write-protect Switch Write-Protect SwitchBar Code Label Using Bar Code Labels PrecautionsGeneral Precautions Usage PrecautionsStorage of Data Cartridges Service LifeStandards for Prohibition of Use Cleaning of the Drive Head Daily MaintenanceCleaning Manually Cleaning of the Drive Head Checking the CLNROL- function Cleaning the Roller inside of the transporterDefault CLNROL-function setting Enable Setting the CLNROL- function Disable Operation Example Changing the RtyCnt valueRtyCnt value in the CLNROL-function Tip Execution timing of the cleaning Cleaning of the RollerTools and Parts Setting Maintenance mode Cleaning the Roller Setting Cleaning modeShows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the interior Cleaning of the Main UnitCleaning of the exterior Cleaning of the fixed slotsCleaning of the cartridge Cleaning of the magazineMovement and Shipping of the Autoloader Phenomenon Recovery Procedure Power Supply TroubleshootingConnections Phenomenon Recovery Procedure Cartridge OperationOthers Phenomenon Recovery Procedure Autoloader PerformanceCleaning Recovery Procedure P move system initialization Exceeding the recommended operation Other Matters to Check When Requesting MaintenanceAutoloader Main Unit Appendix a SpecificationsLTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/N Universal cleaning cartridge TD P/NSupplies Appendix B Optional Items and SuppliesOptional Items CMer Error Code Appendix C Error CodeErr ×××× Messages Related to the Drive Interface MessagesMessage Description Panel Operation and Other MessagesTandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway Tandberg LTO2 Autoloader Installation and User’s Manual
Top Page Image Contents