Tandberg Data Tandberg LTO2 manual Movement and Shipping of the Autoloader, Tip

Page 69

5.2 Movement and Shipping of the Autoloader

Follow the procedure described below when moving or shipping the Autoloader.

Important

When shutting the System, see "2.7 Start and Shut Down of the System".

1.Check that the drive does not contain any cartridges.

2.If there are any cartridges in the drive, eject them. Refer to the manual for the backup software or use the front panel keys. (See "3.5 Operation of Panel Keys" for details.)

3.Remove all cartridges from the Autoloader.

Important

Do not switch off the power of the Autoloader until the interface is in an inactive condition. If the power of a SCSI peripheral device is switched off while the bus is in an active condition, data may be lost or the condition of the bus could become unstable. When the computer is connected to a LAN, be certain to contact the system administrator before switching off the power.

4.Switch off the power of the Autoloader.

5.Disconnect the AC power cable, the SCSI cable, and the terminating resistance connector.

6.House the magazine, and lock the door.

Tip

When shipping this device, please pack it using the original packaging materials and box. If these packaging materials are not available, pack the device using cushioning material so that the device is not subjected to shock at time of shipping.

- 53 -

Image 69

Contents Tandberg LTO2 Autoloader Trademarks FCC Class B NoticeDescription example in this manual Safety DescriptionsMandatory action Prohibited actionGeneral Cautions Safety CautionsDo not apply starburst wiring Do not lift the device alone Do not cover the air inletDo not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Daily Maintenance Chapter TroubleshootingChapter Cartridges Introduction Organization of this manual Symbols used in this manual Symbols used in this manualTip Overview of the Tandberg LTO2 Autoloader Tandberg LTO2 AutoloaderFront Panel of the Tandberg LTO2 Autoloader Names and Functions of the Parts･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display LCD Liquid Crystal DisplayTransfer or Disposal of the Device Handling PrecautionsMain Unit CartridgesContents of the Carton Setup Preparation Before UseTransporter Locking Screw Instruction TAG Storing the Transporter Locking Screw for later use Scsi Cable ConnectionsAC Power Cable Connection AC Power Cable ConnectionAttaching and removing a Filter Element Attaching and removing the Filter ElementScsi ID Setting Switching on the Power Switch and the Power-On SequenceStart and Shutdown of the System Removal of the Magazine OperationLoading the Magazine Loading the MagazineLoading to Magazine Loading the CartridgeFor using the Tandberg LTO2 Autoloader w/BCRs optional Loading to the Fixed SlotsOperation Examples For using the Tandberg LTO2 Autoloader w/BCR Removal from and Insertion to the Magazine Removal and Insertion of the CartridgesDisplay Eject Slot? Removal from and Insertion to the Fixed SlotsFunctions of the Switches Organization of the Front Panel SwitchesOperation of the Panel Keys Slot Logical NumbersPanel Operation Procedure Display Frm Slt 1? Menu Tree 1 Main Menu Menu CommandsRetry Mode Checking the Scsi ID Setting the Scsi IDOperation Example Changing the Scsi IDTip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release KeyCartridges CartridgesData Cartridge Cleaning CartridgeSetting the Write-protect Switch Write-Protect SwitchBar Code Label Using Bar Code Labels PrecautionsGeneral Precautions Usage PrecautionsService Life Standards for Prohibition of UseStorage of Data Cartridges Daily Maintenance CleaningCleaning of the Drive Head Manually Cleaning of the Drive Head Cleaning the Roller inside of the transporter Default CLNROL-function setting EnableChecking the CLNROL- function Setting the CLNROL- function Disable Changing the RtyCnt value RtyCnt value in the CLNROL-functionOperation Example Tip Execution timing of the cleaning Cleaning of the RollerTools and Parts Setting Maintenance mode Cleaning the Roller Setting Cleaning modeShows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the exterior Cleaning of the Main UnitCleaning of the fixed slots Cleaning of the interiorCleaning of the cartridge Cleaning of the magazineMovement and Shipping of the Autoloader Phenomenon Recovery Procedure Power Supply TroubleshootingConnections Phenomenon Recovery Procedure Cartridge OperationPhenomenon Recovery Procedure Autoloader Performance CleaningOthers Recovery Procedure P move system initialization Exceeding the recommended operation Other Matters to Check When Requesting MaintenanceAutoloader Main Unit Appendix a SpecificationsLTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/N Universal cleaning cartridge TD P/NAppendix B Optional Items and Supplies Optional ItemsSupplies CMer Error Code Appendix C Error CodeErr ×××× Messages Related to the Drive Interface MessagesMessage Description Panel Operation and Other MessagesTandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway Tandberg LTO2 Autoloader Installation and User’s Manual