Tandberg Data Tandberg LTO2 manual Start and Shutdown of the System

Page 29

2.7 Start and Shutdown of the System

When the SCSI ID settings have been completed, switch on the power of the server/workstation and the other devices and start the system.

To start the system, switch ON the power in the order of the Autoloader (along with the peripherals connected to the server/workstation) and then the server/workstation.

Important

If the data cartridge is loaded into the tape drive before starting the system, the reading/writing of data recorded on the data cartridge may not be performed properly.

To shut down the system, switch OFF the power in the order of the server/workstation and then the Autoloader (along with the peripherals connected to the server/workstation).

Important

･Before shutting down the system, check that a data cartridge is not loaded in the tape drive. If the system is shut down while the data cartridge is still loaded in the tape drive, the next time the system is started, the reading/writing of data recorded on the data cartridge may not be performed properly or this could cause damage to the data cartridge or this device.

･Do not shut down or restart the system while this device is operating. Check that this device is stopped before closing down or restarting the system.

Important

If an error message is shown as "Unreadable Media" on the PC console’s screen without front panel LED lighting solid red during the following operations, Inventory, Erase, Backup, Restore and etc., please retry the same operation. Also if the cartridge remains in the drive, please eject the cartridge from the drive by manual operation (refer “3.5 Operation of the Panel Keys”) before retrying the operation.

- 13 -

Image 29

Contents Tandberg LTO2 Autoloader Trademarks FCC Class B NoticeDescription example in this manual Safety DescriptionsMandatory action Prohibited actionGeneral Cautions Safety CautionsDo not apply starburst wiring Do not lift the device alone Do not cover the air inletDo not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Cartridges Chapter Daily MaintenanceChapter Troubleshooting Introduction Organization of this manual Tip Symbols used in this manualSymbols used in this manual Overview of the Tandberg LTO2 Autoloader Tandberg LTO2 AutoloaderFront Panel of the Tandberg LTO2 Autoloader Names and Functions of the Parts･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display LCD Liquid Crystal DisplayTransfer or Disposal of the Device Handling PrecautionsMain Unit CartridgesContents of the Carton Transporter Locking Screw Instruction TAG SetupPreparation Before Use Storing the Transporter Locking Screw for later use Scsi Cable ConnectionsAC Power Cable Connection AC Power Cable ConnectionAttaching and removing a Filter Element Attaching and removing the Filter ElementScsi ID Setting Switching on the Power Switch and the Power-On SequenceStart and Shutdown of the System Removal of the Magazine OperationLoading the Magazine Loading the MagazineLoading to Magazine Loading the CartridgeOperation Examples For using the Tandberg LTO2 Autoloader w/BCRs optionalLoading to the Fixed Slots For using the Tandberg LTO2 Autoloader w/BCR Removal from and Insertion to the Magazine Removal and Insertion of the CartridgesDisplay Eject Slot? Removal from and Insertion to the Fixed SlotsFunctions of the Switches Organization of the Front Panel SwitchesOperation of the Panel Keys Slot Logical NumbersPanel Operation Procedure Display Frm Slt 1? Menu Tree 1 Main Menu Menu CommandsRetry Mode Checking the Scsi ID Setting the Scsi IDOperation Example Changing the Scsi IDTip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release KeyCartridges CartridgesData Cartridge Cleaning CartridgeSetting the Write-protect Switch Write-Protect SwitchBar Code Label Using Bar Code Labels PrecautionsGeneral Precautions Usage PrecautionsStorage of Data Cartridges Service LifeStandards for Prohibition of Use Cleaning of the Drive Head Daily MaintenanceCleaning Manually Cleaning of the Drive Head Checking the CLNROL- function Cleaning the Roller inside of the transporterDefault CLNROL-function setting Enable Setting the CLNROL- function Disable Operation Example Changing the RtyCnt valueRtyCnt value in the CLNROL-function Tip Execution timing of the cleaning Cleaning of the RollerTools and Parts Setting Maintenance mode Cleaning the Roller Setting Cleaning modeShows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the exterior Cleaning of the Main UnitCleaning of the fixed slots Cleaning of the interiorCleaning of the cartridge Cleaning of the magazineMovement and Shipping of the Autoloader Phenomenon Recovery Procedure Power Supply TroubleshootingConnections Phenomenon Recovery Procedure Cartridge OperationOthers Phenomenon Recovery Procedure Autoloader PerformanceCleaning Recovery Procedure P move system initialization Exceeding the recommended operation Other Matters to Check When Requesting MaintenanceAutoloader Main Unit Appendix a SpecificationsLTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/N Universal cleaning cartridge TD P/NSupplies Appendix B Optional Items and SuppliesOptional Items CMer Error Code Appendix C Error CodeErr ×××× Messages Related to the Drive Interface MessagesMessage Description Panel Operation and Other MessagesTandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway Tandberg LTO2 Autoloader Installation and User’s Manual