Tandberg Data Tandberg LTO2 manual Manually Cleaning of the Drive Head, Operation

Page 54

5.1.1.1 Manually Cleaning of the Drive Head

Operation 1

Operation 2

Load the cleaning cartridge supplied with the main unit into any of the slots. The cleaning cartridge is housed in slot number 5 in this example.

Use the panel keys to load the cleaning cartridge into the drive. (Cleaning will start automatically.)

Display: cleaning (Displayed during cleaning.)

Operation 3 When cleaning is completed, "DRV full" is displayed. Display: DRV full

Operation 4 Press the ENTER key.

Display: STATUS

Operation 5 Press the arrow key and select the "EJECT" command. Display: EJECT

Operation 6 Press the ENTER key and define the "EJECT" command. Display: Eject Drv?

Operation 6 Press the ENTER key and define the command. Display: To Slot 1?

Operation 7 Press the arrow key and select "To Slot 5?". Display: To Slot 5?

Operation 8 Press the ENTER key and select the command.

Display: Complete (when the command ends normally.)

Err. xxxxxx (when an error occurs. xxxxxx is the error code.)

- 38 -

Image 54

Contents Tandberg LTO2 Autoloader FCC Class B Notice TrademarksSafety Descriptions Description example in this manualProhibited action Mandatory actionSafety Cautions General CautionsDo not apply starburst wiring Do not cover the air inlet Do not lift the device aloneDo not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Daily Maintenance Chapter TroubleshootingChapter Cartridges Introduction Organization of this manual Symbols used in this manual Symbols used in this manualTip Tandberg LTO2 Autoloader Overview of the Tandberg LTO2 AutoloaderNames and Functions of the Parts Front Panel of the Tandberg LTO2 Autoloader･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display Liquid Crystal Display LCDMain Unit Handling PrecautionsTransfer or Disposal of the Device CartridgesContents of the Carton Setup Preparation Before UseTransporter Locking Screw Instruction TAG Scsi Cable Connections Storing the Transporter Locking Screw for later useAC Power Cable Connection AC Power Cable ConnectionAttaching and removing the Filter Element Attaching and removing a Filter ElementSwitching on the Power Switch and the Power-On Sequence Scsi ID SettingStart and Shutdown of the System Operation Removal of the MagazineLoading the Magazine Loading the MagazineLoading the Cartridge Loading to MagazineFor using the Tandberg LTO2 Autoloader w/BCRs optional Loading to the Fixed SlotsOperation Examples For using the Tandberg LTO2 Autoloader w/BCR Removal and Insertion of the Cartridges Removal from and Insertion to the MagazineRemoval from and Insertion to the Fixed Slots Display Eject Slot?Operation of the Panel Keys Organization of the Front Panel SwitchesFunctions of the Switches Slot Logical NumbersPanel Operation Procedure Display Frm Slt 1? Menu Commands Menu Tree 1 Main MenuRetry Mode Setting the Scsi ID Checking the Scsi IDChanging the Scsi ID Operation ExampleTip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release KeyCartridges CartridgesCleaning Cartridge Data CartridgeWrite-Protect Switch Setting the Write-protect SwitchUsing Bar Code Labels Precautions Bar Code LabelUsage Precautions General PrecautionsService Life Standards for Prohibition of UseStorage of Data Cartridges Daily Maintenance CleaningCleaning of the Drive Head Manually Cleaning of the Drive Head Cleaning the Roller inside of the transporter Default CLNROL-function setting EnableChecking the CLNROL- function Setting the CLNROL- function Disable Changing the RtyCnt value RtyCnt value in the CLNROL-functionOperation Example Tip Cleaning of the Roller Execution timing of the cleaningTools and Parts Setting Maintenance mode Setting Cleaning mode Cleaning the RollerShows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the fixed slots Cleaning of the Main UnitCleaning of the exterior Cleaning of the interiorCleaning of the magazine Cleaning of the cartridgeMovement and Shipping of the Autoloader Troubleshooting Phenomenon Recovery Procedure Power SupplyPhenomenon Recovery Procedure Cartridge Operation ConnectionsPhenomenon Recovery Procedure Autoloader Performance CleaningOthers Recovery Procedure P move system initialization Exceeding the recommended operation When Requesting Maintenance Other Matters to CheckAppendix a Specifications Autoloader Main UnitUniversal cleaning cartridge TD P/N LTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/NAppendix B Optional Items and Supplies Optional ItemsSupplies Appendix C Error Code CMer Error CodeErr ×××× Messages Messages Related to the Drive InterfacePanel Operation and Other Messages Message DescriptionTandberg LTO2 Autoloader Installation and User’s Manual Tandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway