Tandberg Data Tandberg LTO2 manual Messages Related to the Drive Interface

Page 83

Messages

Messages such as the following are displayed as required.

Messages Related to the Drive Interface

		Table-D6	Table of Messages Related to the Drive Interface

	Message		Description

	Drive status

	Calibrate	The drive is being calibrated.

	Cleaning	The drive is being cleaned.

	Erasing	The drive is erasing.

	Loading	The drive is loading.

	Locating	The drive is locating.

	Reading	The drive is reading.

	Rewinding	The drive is rewinding.

	REQ clean	The drive is requesting a cleaning.

	Unloading	The drive is unloading.

	Wait load	Waiting for loading completion following execution of the Load command.

	Wait unload	Waiting for unloading completion following execution of the Unload command.

	Writing	The drive is writing.

	DRV full	There is a cartridge in the drive.

	DRV empty	There isn't a cartridge in the drive.

	Autoloader and Drive

	COMM.ERROR	The Autoloader detected a communication error with the drive.

	Drive error and caution

	DRV Err 1	There has been detection of the drive exceeding the recommended operation temperature.

	DRV Err 2	There has been detection of the drive input voltage reaching the limit of or exceeding the
	DRV Err 2	permissible range.
		permissible range.
	DRV Err 3	A drive firmware error has occurred.

	DRV Err 4	A fault has occurred in the drive firmware or hardware.

	DRV Err 5	A fault has occurred in the drive hardware.

	DRV Err 6	A drive hardware or a media error has occurred.

	DRV Err 7	A fault of the media has occurred.

	DRV Err 8	An error has occurred in the drive hardware or SCSI bus.

	DRV Err 9	An error has occurred in the drive hardware or RS-422 connection.

	DRV Err A	An error has occurred in the drive hardware.

- 67 -

Image 83

Contents Tandberg LTO2 Autoloader Trademarks FCC Class B NoticeDescription example in this manual Safety DescriptionsMandatory action Prohibited actionGeneral Cautions Safety CautionsDo not apply starburst wiring Do not lift the device alone Do not cover the air inletDo not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Cartridges Chapter Daily MaintenanceChapter Troubleshooting Introduction Organization of this manual Tip Symbols used in this manualSymbols used in this manual Overview of the Tandberg LTO2 Autoloader Tandberg LTO2 AutoloaderFront Panel of the Tandberg LTO2 Autoloader Names and Functions of the Parts･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display LCD Liquid Crystal DisplayCartridges Handling PrecautionsTransfer or Disposal of the Device Main UnitContents of the Carton Transporter Locking Screw Instruction TAG SetupPreparation Before Use Storing the Transporter Locking Screw for later use Scsi Cable ConnectionsAC Power Cable Connection AC Power Cable ConnectionAttaching and removing a Filter Element Attaching and removing the Filter ElementScsi ID Setting Switching on the Power Switch and the Power-On SequenceStart and Shutdown of the System Removal of the Magazine OperationLoading the Magazine Loading the MagazineLoading to Magazine Loading the CartridgeOperation Examples For using the Tandberg LTO2 Autoloader w/BCRs optionalLoading to the Fixed Slots For using the Tandberg LTO2 Autoloader w/BCR Removal from and Insertion to the Magazine Removal and Insertion of the CartridgesDisplay Eject Slot? Removal from and Insertion to the Fixed SlotsSlot Logical Numbers Organization of the Front Panel SwitchesFunctions of the Switches Operation of the Panel KeysPanel Operation Procedure Display Frm Slt 1? Menu Tree 1 Main Menu Menu CommandsRetry Mode Checking the Scsi ID Setting the Scsi IDOperation Example Changing the Scsi IDTip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release KeyCartridges CartridgesData Cartridge Cleaning CartridgeSetting the Write-protect Switch Write-Protect SwitchBar Code Label Using Bar Code Labels PrecautionsGeneral Precautions Usage PrecautionsStorage of Data Cartridges Service LifeStandards for Prohibition of Use Cleaning of the Drive Head Daily MaintenanceCleaning Manually Cleaning of the Drive Head Checking the CLNROL- function Cleaning the Roller inside of the transporterDefault CLNROL-function setting Enable Setting the CLNROL- function Disable Operation Example Changing the RtyCnt valueRtyCnt value in the CLNROL-function Tip Execution timing of the cleaning Cleaning of the RollerTools and Parts Setting Maintenance mode Cleaning the Roller Setting Cleaning modeShows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the interior Cleaning of the Main UnitCleaning of the exterior Cleaning of the fixed slotsCleaning of the cartridge Cleaning of the magazineMovement and Shipping of the Autoloader Phenomenon Recovery Procedure Power Supply TroubleshootingConnections Phenomenon Recovery Procedure Cartridge OperationOthers Phenomenon Recovery Procedure Autoloader PerformanceCleaning Recovery Procedure P move system initialization Exceeding the recommended operation Other Matters to Check When Requesting MaintenanceAutoloader Main Unit Appendix a SpecificationsLTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/N Universal cleaning cartridge TD P/NSupplies Appendix B Optional Items and SuppliesOptional Items CMer Error Code Appendix C Error CodeErr ×××× Messages Related to the Drive Interface MessagesMessage Description Panel Operation and Other MessagesTandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway Tandberg LTO2 Autoloader Installation and User’s Manual