Tandberg Data Tandberg LTO2 manual Using Bar Code Labels Precautions

Page 50

4.3 Bar Code Label

The bar code label contains;

A volume serial number that you can read.

A bar code label that the Tandberg LTO2 Autoloader can read.

When appling a bar code labels to a cartridge position the bar code label only

in the recessed label area (see below figure). A bar code label that extends outside of this

recessed area can cause reading problems in the internal LTO drive or the robotics of the TD LTO2 Autoloader.

Sample Bar Code Label on the cartridge

Figure 4-3 Sample Bar Code Label on the Cartridge

Tip

Do not place any type of mark on the white space area at either end of the bar code. A mark in this area may prevent the Tandberg LTO2 Autoloader from reading the bar code label.

Using Bar Code Labels Precautions

When using a bar code labels, please observe the following precautions.

Use only TANDBERG DATA-supplied bar code labels.

Do not re-use a bar code label or re-apply a used bar code label over an existing label.

Before you apply a new bar code label, remove the old label by gently pulling it.

Remove the bar code label from the label sheet carefully. Do not stretch the bar code label or cause the edges to curl.

Position the bar code label within the recessed label area..

Do not place other autoloader readable bar code labels on other surfaces of the cartridge. They may interfere with the ability of the bar code reader to read the bar code.

-34 -

Image 50
Contents Tandberg LTO2 Autoloader FCC Class B Notice TrademarksSafety Descriptions Description example in this manualProhibited action Mandatory actionSafety Cautions General CautionsDo not apply starburst wiring Do not cover the air inlet Do not lift the device aloneDo not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Cartridges Chapter Daily MaintenanceChapter Troubleshooting Introduction Organization of this manual Tip Symbols used in this manualSymbols used in this manual Tandberg LTO2 Autoloader Overview of the Tandberg LTO2 AutoloaderNames and Functions of the Parts Front Panel of the Tandberg LTO2 Autoloader・ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display Liquid Crystal Display LCDMain Unit Handling PrecautionsTransfer or Disposal of the Device CartridgesContents of the Carton Transporter Locking Screw Instruction TAG SetupPreparation Before Use Scsi Cable Connections Storing the Transporter Locking Screw for later useAC Power Cable Connection AC Power Cable ConnectionAttaching and removing the Filter Element Attaching and removing a Filter ElementSwitching on the Power Switch and the Power-On Sequence Scsi ID SettingStart and Shutdown of the System Operation Removal of the MagazineLoading the Magazine Loading the MagazineLoading the Cartridge Loading to MagazineOperation Examples For using the Tandberg LTO2 Autoloader w/BCRs optionalLoading to the Fixed Slots For using the Tandberg LTO2 Autoloader w/BCR Removal and Insertion of the Cartridges Removal from and Insertion to the MagazineRemoval from and Insertion to the Fixed Slots Display Eject Slot?Operation of the Panel Keys Organization of the Front Panel SwitchesFunctions of the Switches Slot Logical NumbersPanel Operation Procedure Display Frm Slt 1? Menu Commands Menu Tree 1 Main MenuRetry Mode Setting the Scsi ID Checking the Scsi IDChanging the Scsi ID Operation ExampleTip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release KeyCartridges CartridgesCleaning Cartridge Data CartridgeWrite-Protect Switch Setting the Write-protect SwitchUsing Bar Code Labels Precautions Bar Code LabelUsage Precautions General PrecautionsStorage of Data Cartridges Service LifeStandards for Prohibition of Use Cleaning of the Drive Head Daily MaintenanceCleaning Manually Cleaning of the Drive Head Checking the CLNROL- function Cleaning the Roller inside of the transporterDefault CLNROL-function setting Enable Setting the CLNROL- function Disable Operation Example Changing the RtyCnt valueRtyCnt value in the CLNROL-function Tip Cleaning of the Roller Execution timing of the cleaningTools and Parts Setting Maintenance mode Setting Cleaning mode Cleaning the RollerShows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the fixed slots Cleaning of the Main UnitCleaning of the exterior Cleaning of the interiorCleaning of the magazine Cleaning of the cartridgeMovement and Shipping of the Autoloader Troubleshooting Phenomenon Recovery Procedure Power SupplyPhenomenon Recovery Procedure Cartridge Operation ConnectionsOthers Phenomenon Recovery Procedure Autoloader PerformanceCleaning Recovery Procedure P move system initialization Exceeding the recommended operation When Requesting Maintenance Other Matters to CheckAppendix a Specifications Autoloader Main UnitUniversal cleaning cartridge TD P/N LTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/NSupplies Appendix B Optional Items and SuppliesOptional Items Appendix C Error Code CMer Error CodeErr ×××× Messages Messages Related to the Drive InterfacePanel Operation and Other Messages Message DescriptionTandberg LTO2 Autoloader Installation and User’s Manual Tandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway