Tandberg Data Tandberg LTO2 manual Setup, Preparation Before Use

Page 24

Chapter2 Setup

This chapter describes the procedure for connecting the Autoloader to a basic processing device such as a server or workstation.

Important

Maintenance personnel will perform the rack installation or removal work for the Tandberg LTO2 Autoloader.

2.1 Preparation Before Use

Before using the Autoloader, remove the transporter locking screw that is a type of thumbscrew located at the left side of the decorative cover.

Important

Remove the transporter locking screw before switching ON the power switch. Switching ON the power while the transporter locking screw is still attached could result in damage to the Autoloader.

Removal of the Transporter Locking Screw and Instruction TAG

1.To loosen this screw turn to counterclockwise by hand.

2.Remove the Instruction TAG with the Transporter Locking Screw (see figure 2-1).

3.As the Transporter Locking Screw will be needed to ship or move the Autoloader, insert it into the hole and tighten to keep it (see figure 2-2).

Transporter Locking Screw

Instruction TAG

Figure 2-1 Removal of the Transporter Locking Screw and Instruction TAG

- 8 -

Image 24

Contents Tandberg LTO2 Autoloader FCC Class B Notice TrademarksSafety Descriptions Description example in this manualProhibited action Mandatory actionSafety Cautions General CautionsDo not apply starburst wiring Do not cover the air inlet Do not lift the device aloneDo not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Daily Maintenance Chapter TroubleshootingChapter Cartridges Introduction Organization of this manual Symbols used in this manual Symbols used in this manualTip Tandberg LTO2 Autoloader Overview of the Tandberg LTO2 AutoloaderNames and Functions of the Parts Front Panel of the Tandberg LTO2 Autoloader･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display Liquid Crystal Display LCDHandling Precautions Transfer or Disposal of the DeviceMain Unit CartridgesContents of the Carton Setup Preparation Before UseTransporter Locking Screw Instruction TAG Scsi Cable Connections Storing the Transporter Locking Screw for later useAC Power Cable Connection AC Power Cable ConnectionAttaching and removing the Filter Element Attaching and removing a Filter ElementSwitching on the Power Switch and the Power-On Sequence Scsi ID SettingStart and Shutdown of the System Operation Removal of the MagazineLoading the Magazine Loading the MagazineLoading the Cartridge Loading to MagazineFor using the Tandberg LTO2 Autoloader w/BCRs optional Loading to the Fixed SlotsOperation Examples For using the Tandberg LTO2 Autoloader w/BCR Removal and Insertion of the Cartridges Removal from and Insertion to the MagazineRemoval from and Insertion to the Fixed Slots Display Eject Slot?Organization of the Front Panel Switches Functions of the SwitchesOperation of the Panel Keys Slot Logical NumbersPanel Operation Procedure Display Frm Slt 1? Menu Commands Menu Tree 1 Main MenuRetry Mode Setting the Scsi ID Checking the Scsi IDChanging the Scsi ID Operation ExampleTip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release KeyCartridges CartridgesCleaning Cartridge Data CartridgeWrite-Protect Switch Setting the Write-protect SwitchUsing Bar Code Labels Precautions Bar Code LabelUsage Precautions General PrecautionsService Life Standards for Prohibition of UseStorage of Data Cartridges Daily Maintenance CleaningCleaning of the Drive Head Manually Cleaning of the Drive Head Cleaning the Roller inside of the transporter Default CLNROL-function setting EnableChecking the CLNROL- function Setting the CLNROL- function Disable Changing the RtyCnt value RtyCnt value in the CLNROL-functionOperation Example Tip Cleaning of the Roller Execution timing of the cleaningTools and Parts Setting Maintenance mode Setting Cleaning mode Cleaning the RollerShows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the Main Unit Cleaning of the exteriorCleaning of the fixed slots Cleaning of the interiorCleaning of the magazine Cleaning of the cartridgeMovement and Shipping of the Autoloader Troubleshooting Phenomenon Recovery Procedure Power SupplyPhenomenon Recovery Procedure Cartridge Operation ConnectionsPhenomenon Recovery Procedure Autoloader Performance CleaningOthers Recovery Procedure P move system initialization Exceeding the recommended operation When Requesting Maintenance Other Matters to CheckAppendix a Specifications Autoloader Main UnitUniversal cleaning cartridge TD P/N LTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/NAppendix B Optional Items and Supplies Optional ItemsSupplies Appendix C Error Code CMer Error CodeErr ×××× Messages Messages Related to the Drive InterfacePanel Operation and Other Messages Message DescriptionTandberg LTO2 Autoloader Installation and User’s Manual Tandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway