Tandberg Data Tandberg LTO2 Safety Descriptions, Description example in this manual

Page 3

Keep this operation manual on hand so that you can refer to it when needed. Be sure to read “Safety Precautions” before using this product.

Safety Precautions- Be sure to read this section before using this product. –

Safety Descriptions

This manual describes dangers that may be caused by ignoring the cautions and the ways to avoid those dangers. Warning labels are attached on the components that may cause danger.

“Warning” and “caution” terms are used for warning labels to describe the degree of the danger.

WARNING

CAUTION

This indicates a hazard that could lead to death or serious injury in the event of improper handling.

This indicates a hazard that could lead to burns, injury, or property damage in the event of improper handling.

The following three types of symbols are used for warnings and cautions. The meaning of each symbol is described below.

 

 

 

 

This symbol indicates that danger could be

(Ex)

 

 

 

Attention

caused if instructions are ignored. The

 

 

 

figure in the symbol indicates details of the

(CAUTION:

 

 

 

 

 

 

 

 

danger.

 

 

 

 

Electric shock)

 

 

 

Prohibited

This symbol indicates prohibited action. The

(Ex)

 

 

 

figure in the symbol or near the symbol

 

 

 

 

action

 

 

 

 

indicates details of the prohibited action.

(Do not

 

 

 

 

 

 

 

 

 

disassemble.)

 

 

 

Mandatory

This symbol indicates mandatory action.

(Ex)

 

 

 

The figure in the symbol indicates details of

 

 

 

 

action

the mandatory action. The mandatory action

 

 

 

 

 

is required to avoid danger.

(Unplug)

 

 

 

 

 

(Description example in this manual)

Term indicating the degree of danger

Details of caution to avoid danger

CAUTION

Only plug into specified electric outlet.

Plug the power supply cable into an electric outlet on the wall with specified voltage and power supply. Fire or electric leak may be caused if power supply other than the one specified is used.

Symbol prompting the caution

- i -

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Tandberg LTO2 Autoloader Trademarks FCC Class B NoticeDescription example in this manual Safety DescriptionsMandatory action Prohibited actionGeneral Cautions Safety CautionsDo not apply starburst wiring Do not lift the device alone Do not cover the air inletDo not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Daily Maintenance Chapter TroubleshootingChapter Cartridges Introduction Organization of this manual Symbols used in this manual Symbols used in this manualTip Overview of the Tandberg LTO2 Autoloader Tandberg LTO2 AutoloaderFront Panel of the Tandberg LTO2 Autoloader Names and Functions of the Parts･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display LCD Liquid Crystal DisplayCartridges Handling PrecautionsTransfer or Disposal of the Device Main UnitContents of the Carton Setup Preparation Before UseTransporter Locking Screw Instruction TAG Storing the Transporter Locking Screw for later use Scsi Cable ConnectionsAC Power Cable Connection AC Power Cable ConnectionAttaching and removing a Filter Element Attaching and removing the Filter ElementScsi ID Setting Switching on the Power Switch and the Power-On SequenceStart and Shutdown of the System Removal of the Magazine OperationLoading the Magazine Loading the MagazineLoading to Magazine Loading the CartridgeFor using the Tandberg LTO2 Autoloader w/BCRs optional Loading to the Fixed SlotsOperation Examples For using the Tandberg LTO2 Autoloader w/BCR Removal from and Insertion to the Magazine Removal and Insertion of the CartridgesDisplay Eject Slot? Removal from and Insertion to the Fixed SlotsSlot Logical Numbers Organization of the Front Panel SwitchesFunctions of the Switches Operation of the Panel KeysPanel Operation Procedure Display Frm Slt 1? Menu Tree 1 Main Menu Menu CommandsRetry Mode Checking the Scsi ID Setting the Scsi IDOperation Example Changing the Scsi IDTip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release KeyCartridges CartridgesData Cartridge Cleaning CartridgeSetting the Write-protect Switch Write-Protect SwitchBar Code Label Using Bar Code Labels PrecautionsGeneral Precautions Usage PrecautionsService Life Standards for Prohibition of UseStorage of Data Cartridges Daily Maintenance CleaningCleaning of the Drive Head Manually Cleaning of the Drive Head Cleaning the Roller inside of the transporter Default CLNROL-function setting EnableChecking the CLNROL- function Setting the CLNROL- function Disable Changing the RtyCnt value RtyCnt value in the CLNROL-functionOperation Example Tip Execution timing of the cleaning Cleaning of the RollerTools and Parts Setting Maintenance mode Cleaning the Roller Setting Cleaning modeShows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the interior Cleaning of the Main UnitCleaning of the exterior Cleaning of the fixed slotsCleaning of the cartridge Cleaning of the magazineMovement and Shipping of the Autoloader Phenomenon Recovery Procedure Power Supply TroubleshootingConnections Phenomenon Recovery Procedure Cartridge OperationPhenomenon Recovery Procedure Autoloader Performance CleaningOthers Recovery Procedure P move system initialization Exceeding the recommended operation Other Matters to Check When Requesting MaintenanceAutoloader Main Unit Appendix a SpecificationsLTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/N Universal cleaning cartridge TD P/NAppendix B Optional Items and Supplies Optional ItemsSupplies CMer Error Code Appendix C Error CodeErr ×××× Messages Related to the Drive Interface MessagesMessage Description Panel Operation and Other MessagesTandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway Tandberg LTO2 Autoloader Installation and User’s Manual
Top Page Image Contents