Rockford Fosgate T1000-4 Installation Installation Considerations, Location, +12V DC is applied

Page 5

DESIGN FEATURES

 

 

14.

RCA Pass-Thru Jack – This Pass-Thru provides a convenient source for daisy-chaining an additional

 

amplifier without running an extra set of RCA cables from the front of the vehicle to the rear amplifier

15.

location.

Remote Terminal – This heavy duty, nickel-plated wire connector will accept wire sizes from

 

8 AWG to 16 AWG.This terminal is used to remotely turn-on and turn-off the amplifier when

16.

+12V DC is applied.

Power Terminals – The power and ground connectors on the amplifier are nickel-plated and will

 

accommodate up to 1/0 AWG wire maximizing the input current capability of the amplifier.

INSTALLATION

INSTALLATION CONSIDERATIONS

The following is a list of tools needed for installation:

Fuse-holder and fuse.

Battery post wrench

(See specifications for fuse rating)

Hand held drill w/assorted bits

Volt/Ohm Meter

1/8" diameter heatshrink tubing

Wire strippers

Assorted connectors

Wire crimpers

Adequate Length—Red 1/0 AWGPower Wire

Wire cutters

Adequate Length—Remote Turn-on Wire

#2 Phillips screwdriver

Adequate Length—Black 1/0 AWG Grounding Wire

NOTE:We recommend a 1/0 AWG wire for use on the power (B+) and ground (GND) connections. This section focuses on some of the vehicle considerations for installing your new amplifier. Pre-planning your system layout and best wiring routes will save installation time.When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments.

:If you feel unsure about installing this system yourself, have it installed by a CAUTION qualified technician.

:Before installation, disconnect the battery negative (-) terminal to prevent CAUTION damage to the unit, fire and/or possible injury.

Before beginning any installation, follow these simple rules:

1. Be sure to carefully read and understand the instructions before attempting to install the unit.

2. For safety, disconnect the negative lead from the battery prior to beginning the installation.

3. For easier assembly, we suggest you run all wires prior to mounting your unit in place.

4. Route all of the RCA cables close together and away from any high current wires.

5. Use high quality connectors for a reliable installation and to minimize signal or power loss.

6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.

7. Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.

8. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.

9. ALWAYS protect the battery and electrical system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12V power wire within 18" (45.7 cm) of the battery terminal.

10. When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connections should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle.

5

Image 5
Contents Installation Operation Introduction Table of ContentsContents of Carton Safety InstructionsOutp Design FeaturesProt +12V DC is applied Installation Installation ConsiderationsLocation Wiring the System Installation Mounting LocationsBattery and Charging Power Connection InstallationCrossov r Fr nt & Rear is set Channel Wiring Mono BridgedChannel Wiring Stereo Bridged Quick Install Channel WiringOperation Remote Punch EQ OptionalOperation Punch EQ Adjusting Crossover FrequencyChannel Switch Troubleshooting Operation Adjusting GainMODEL- Power SpecificationsSpecifications subject to change without notice T1000-4Limited Warranty Information Length of WarrantyTable DES Matières Contenu DE Lemballage Consignes DE SécuritéMise EN Garde Particularités Techniques Commande+ et de masse GND Installation Considérations Concernant L’INSTALLATIONAppliquée Batterie ET Charge Installation Emplacements DE MontageCompartiment moteur Montage dans le coffreConnexion Dalimentation Vérifiez les polarités de signal à l’aide des schémasLinstant Ou des arrêts soudains du véhiculePonté mono Câblage à 2 voiesPonté stéréo COM Mutateur DE Canal 2/4Installez Vite Télécommande Dégaliseur Punch en optionFonctionnement Câblage à 4 voi esRéglage DE LA Fréquence DU Filtre Passif Fonctionnement Égaliseur PunchCommutateur DE Canal 2/4 Câbles RCA avant et arrière fermement ensembleDépannage Fonctionnement Réglage DU GainProcédure 2 Le voyant de protection ou thermique est allumé Procédure 3 Vérifiez la sortie audio de lampliLes spécifications sont sujettes à changements sans préavis Modèle PowerCaractéristiques Informations SUR LA Garantie Limitée Durée de la garantieÍndice DE Materias IntroducciónNúmero de la serie Número del modelo NOTALea cada sección para obtener información más detalladaContenido DE LA Caja Instrucciones DE SeguridadPrecaución Características DEL Diseño Vehículo hasta el punto del amplificador trasero Instalación Consideraciones Para LA InstalaciónCuando se aplican +12V de corriente continua Entrada del amplificadorCableado DEL Sistema Instalación Lugares DE MontajeBateríay Carga Daños al amplificador o a los componentes conectados InstalaciónConexión de Corriente Cableado de 4 canales Estéreo ponteado Pontea doFuncionamiento Cableado de 4 canalesRemote Punch EQ Opcional Aprisa InstaleAjuste DE LA Frecuencia X-OVER Transición Funcionamiento Punch EQInterruptor DE 2/4 Canales Trasero muy juntosFuncionamiento Ajuste DE Ganancia Solución DE ProblemasHaga lo siguiente individualmente para cada canal Está encendida vaya al Paso 3,de otra manera,continúeEspecificaciones Modelo PowerInformación Sobre LA Garantía Limitada Duración de la garantíaInhaltsverzeichnis EinleitungSeriennummer Modellnummer Einleitung Sicherheitshinweise DesigncharakteristikenVorsicht SicherheitshinweiseNicht Kopfschmerzen bereitet Qualifizierten Rockford Fosgate Techniker einbauenHinweis DesigncharakteristikenGrößen 8 AWG bis 16 AWG auf Einbauüberlegungen EinbauVerkabelung DES Systems Einbau BefestigungsstellenBatterie UND Aufladung Stromanschlüsse Stereo überbrückt ÜberbrücktVierkanalverkabelung Funktion BetriebPUNCH-EQ-FERNBEDIENUNG wahlweise ZWEI-/VIERKANALSCHALTER Betrieb Punch EQCROSSOVER-FREQUENZ Einstellen Fehlerbeseitigung Betrieb Lautstärke Gain EinstellenVerfahren 2Schutz- oderThermallicht leuchtet auf Verfahren 3DenVerstärker aufAudioleistung überprüfenOrer MODELL- PowerTechnische Daten Die technischen Daten können sich ohne Ankündigung ändernInformationen ZUR Beschränkten Garantie Laufzeit der GarantieIndice IntroduzioneNumero di serie Numero di modello Nota Ripassare ciascuna sezione per ulteriori ragguagliContenuto DELL’IMBALLAGGIO Istruzioni DI SicurezzaAttenzione Soddisfazione, non un mal di capoAutomaticamente Caratteristiche DEL DesignSullamplificatore Con questi amplificatoriConsiderazioni SULL’INSTALLAZIONE InstallazioneCablaggio DEL Sistema Installazione PosizionamentoBatteria E Caricamento Anteriori e posteriori InstallazioneCollegamento Alla tensione Cablaggio a 4 canali Stereo in parallelo Cablaggio a 2 canali Mono ParalleloInterruttore 2/4 Canali in posizione Guadagno anteriore PosterioreCablaggio a 4 canali Rapidamente InstalliFunzionamento Equalizzatore Punch a Distanza opzionaleInterruttore 2/4 Canali Funzionamento Equalizzatore PunchRegolazione Della Frequenza DI Incrocio INDIVIDUAZIONE/RIPARAZIONE Guasti Funzionamento Regolazione DEL GuadagnoOppure Altrimenti continuareSpecifiche Modello PowerOppure Specifiche soggette a modiche senza preavvisoInformazioni Inerenti Alla Garanzia Limitata Lunghezza della garanziaNotas Notas U.S.A., 480 967-3565 Customer Service

T1000-4 specifications

The Rockford Fosgate T1000-4 is a powerful and versatile amplifier designed to deliver high-performance audio output in car audio systems. As part of Rockford Fosgate's Punch series, this amplifier exemplifies the brand’s commitment to quality and innovation, catering to enthusiasts seeking exceptional sound quality and reliability.

One of the standout features of the T1000-4 is its 1000-watt power output, which is capable of driving multiple speakers or subwoofers with ease. It provides flexibility for users looking to build a robust audio system, whether for daily driving or competitive environments. The amplifier is designed with a full-range architecture, allowing it to effectively power a wide range of speakers with great clarity and detail.

The T1000-4 employs a Class AD amplification technology, which combines the efficiency of Class D amplifiers with the sound quality characteristics of Class A/B amplifiers. This design results in lower heat generation and improved energy efficiency, making it ideal for extended listening sessions without the risk of overheating.

Additionally, the amplifier features a variable 12 dB/octave high-pass and low-pass crossover, enabling users to tailor their audio experience according to personal preferences and speaker requirements. The built-in equalizer allows for fine-tuning sound profiles, ensuring that every note and nuance is heard distinctly.

The T1000-4 also boasts a compact design, incorporating advanced heatsinking for effective thermal management. This not only aids in enhancing performance but also facilitates easier installation in various vehicle setups. The amplifier is equipped with high-level inputs, allowing it to connect seamlessly with factory-installed audio systems without requiring additional modifications.

Durability is another hallmark of the T1000-4, featuring a rugged build quality designed to withstand the rigors of automotive environments. The amplifier's connectors are also designed to minimize installation complexity while ensuring a secure connection, contributing to the overall reliability of the system.

In summary, the Rockford Fosgate T1000-4 amplifier stands out for its robust power output, Class AD technology, customizable crossover and equalization settings, along with its compact, durable design. This amplifier is an excellent choice for car audio enthusiasts aiming to achieve a powerful, clear, and dynamic sound experience on the road.