Nortel Networks 4134 quick start Personal safety and equipment protection, Module protection

Page 18

18Secure Router 4134 regulatory information and safety precautions

WARNING

The 2- and 4-port FXS interface modules have a ring signal generator that is a source of hazardous voltage. Do not touch the RJ11 port conductors, the conductors of a cable (that is, the exposed metal ends of a cable connector) connected to the RJ11 port, or the circuit board when the ringer is active (an incoming call activates the ringer).

Foreign Exchange Office (FXO) Interface Modules

ATTENTION

Ensure you use standard straight-through RJ11 modular telephone cables with FXO interface modules. TIP must connect to TIP and RING must connect to RING.

ATTENTION

For connections that pass outside the building in which the Secure Router 4134 resides, you must connect FXO ports through an approved network termination unit that has integrated circuit protection.

WARNING

The 2- and 4-port FXO interface modules have a ring signal generator that is a source of hazardous voltage. Do not touch the RJ11 port conductors, the conductors of a cable (that is, the exposed metal ends of a cable connector) connected to the RJ11 port, or the circuit board when the ringer is active (an incoming call activates the ringer).

Personal safety and equipment protection

Read this section to prevent injury and equipment damage.

Module protection

The following practices prevent equipment damage when you work on the Nortel Secure Router 4134:

•Always wear a grounded antistatic wrist strap when you handle modules.

•Always set modules on appropriate antistatic material.

•Handle modules by the faceplate and handles. Do not touch pins or electrical connections.

•Do not leave interface module or power supply module slots empty. You must fill all slots with modules or slot covers to maintain safety compliance, proper cooling, and electromagnetic interference (EMI) containment in the shelf.

Nortel Secure Router 4134

Quick Start

NN47263-100 02.01 Standard

18 February 2008

Copyright © 2007, 2008 Nortel Networks

Image 18

Contents Quick Start Page Contents Introduction Power cord warning statement Copyright 2007, 2008 Nortel Networks International Regulatory Statements of Conformity FCC statement USA onlyTIA-968-A CE marking statement Europe only EN 55022 statementsEN 55024 statement EN 300386 statementVcci statement Japan/Nippon only Bsmi statement Taiwan onlyMIC notice Republic of Korea only NOM statement Mexico only National Safety Statements of ComplianceEN 60950 statement Información NOM unicamente para MéxicoNational Environmental Statements of Compliance Denan statement Japan/Nippon onlyRoHS Directive Compliance Statement Safety messages Weee Directive Compliance StatementWarnung Warnung Hardware Notice Foreign Exchange Station FXS Interface Modules Risiko einer Augenverletzung durch LaserPersonal safety and equipment protection Foreign Exchange Office FXO Interface ModulesModule protection Cables and connectors protection Electrostatic dischargeAntistatic material Features Interface modulesNew in this release Introduction NavigationIntroduction Secure Router 4134 installation and initial configuration Secure Router 4134 installation and initial configuration Copyright 2007, 2008 Nortel Networks Secure Router 4134 installation and initial configuration Unpacking and inspecting the Secure Router 4134 chassis Step ActionInstalling a power supply module Secure Router 4134 accessories Accessory Function VerifiedInstalling the mounting brackets on the chassis PrerequisitesAverage time to install mounting brackets 2 minutes Prerequisites Installing the chassis Risk of injury Grounding the chassis Grounding the chassis Achtung Installing the interface modules Slot numbering legend printed on the Secure Router Installing a Small Module Foreign Exchange Office FXO Interface ModulesInstalling a Medium Module Installing a Large ModuleInstalling a Small Module in the Voice Carrier Medium Module Voice Carrier Medium Module slot numbering Prerequisites Connecting power cables Connecting AC power cablesConnecting DC power Average time to install one DC power cable 3 minutes Switch off the DC power source Copyright 2007, 2008 Nortel Networks End Powering up the router Verifying a successful installationLogon prompt appears on the console screen Copyright 2007, 2008 Nortel Networks Configuring the Secure Router 4134 for remote access Connecting a terminal for local accessEstablishing remote access Using SSH for remote access Login admin Password setupChanging the default administrator password EnableChanging the default administrator password Configuring the Secure Router 4134 for remote access Appendix Environmental requirements Environmental requirements Appendix Translations of safety messages Class a device caution statementQualified service personnel warning statement CuidadoOvercurrent warning statement AvisoCover plate warning statement Power cord warning statement Peligro Page Quick Start