Nortel Networks 4134 quick start Establishing remote access, Prerequisites

Page 56

56Configuring the Secure Router 4134 for remote access

Prerequisites

•Ensure you have the supplied console cable.

•Ensure you have the supplied female DB-9 to RJ-45 adapter if you require it for connection to your terminal or PC.

•Ensure you have the Secure Router 4134 securely installed in the equipment rack.

•Ensure you have powered up the terminal or PC.

Procedure steps

Step Action

1Set the terminal protocol as follows: a 9600 baud

b 8 data bits c 1 stop bit d no parity

e flow control: None

2Insert the male RJ-45 connector in the console port on the rear panel of the Secure Router 4134.

3Connect the female DB-9 to RJ-45 adapter to the opposite end of the console cable, if necessary.

4Insert the RJ-45 or female DB-9 connector (dependent on your equipment) in a terminal or PC.

5Power up the Secure Router 4134.

--End--

Establishing remote access

The first time you log on to the Secure Router 4134 CLI, you perform initial configuration such as the following:

1.Configure the IP address for the management port.

2.Configure the next hop (gateway IP address).

3.Verify a successful connection.

4.Enable remote access.

You can enable SSH or Telnet for remote connections.

Nortel Secure Router 4134

Quick Start

NN47263-100 02.01 Standard

18 February 2008

Copyright © 2007, 2008 Nortel Networks

Image 56

Contents Quick Start Page Contents Introduction Power cord warning statement Copyright 2007, 2008 Nortel Networks International Regulatory Statements of Conformity FCC statement USA onlyTIA-968-A CE marking statement Europe only EN 55022 statementsEN 55024 statement EN 300386 statementMIC notice Republic of Korea only Vcci statement Japan/Nippon onlyBsmi statement Taiwan only National Safety Statements of Compliance EN 60950 statementNOM statement Mexico only Información NOM unicamente para MéxicoRoHS Directive Compliance Statement National Environmental Statements of ComplianceDenan statement Japan/Nippon only Safety messages Weee Directive Compliance StatementWarnung Warnung Hardware Notice Foreign Exchange Station FXS Interface Modules Risiko einer Augenverletzung durch LaserModule protection Personal safety and equipment protectionForeign Exchange Office FXO Interface Modules Cables and connectors protection Electrostatic dischargeAntistatic material Features Interface modulesNew in this release Introduction NavigationIntroduction Secure Router 4134 installation and initial configuration Secure Router 4134 installation and initial configuration Copyright 2007, 2008 Nortel Networks Secure Router 4134 installation and initial configuration Unpacking and inspecting the Secure Router 4134 chassis Step ActionInstalling a power supply module Secure Router 4134 accessories Accessory Function VerifiedInstalling the mounting brackets on the chassis PrerequisitesAverage time to install mounting brackets 2 minutes Prerequisites Installing the chassis Risk of injury Grounding the chassis Grounding the chassis Achtung Installing the interface modules Slot numbering legend printed on the Secure Router Installing a Small Module Foreign Exchange Office FXO Interface ModulesInstalling a Medium Module Installing a Large ModuleInstalling a Small Module in the Voice Carrier Medium Module Voice Carrier Medium Module slot numbering Prerequisites Connecting power cables Connecting AC power cablesConnecting DC power Average time to install one DC power cable 3 minutes Switch off the DC power source Copyright 2007, 2008 Nortel Networks End Powering up the router Verifying a successful installationLogon prompt appears on the console screen Copyright 2007, 2008 Nortel Networks Configuring the Secure Router 4134 for remote access Connecting a terminal for local accessEstablishing remote access Using SSH for remote access Login admin Password setupChanging the default administrator password EnableChanging the default administrator password Configuring the Secure Router 4134 for remote access Appendix Environmental requirements Environmental requirements Appendix Translations of safety messages Class a device caution statementQualified service personnel warning statement CuidadoOvercurrent warning statement AvisoCover plate warning statement Power cord warning statement Peligro Page Quick Start