Nortel Networks 4134 quick start Powering up the router, Verifying a successful installation

Page 52

52Installing the Secure Router 4134 chassis and hardware components

Powering up the router

Use the procedure in this section to power up your Secure Router 4134.

Prerequisites

•Ensure all installation procedures are complete.

•Ensure an operator console is connected to the Secure Router 4134.

•Ensure the Secure Router 4134 is connected to a power source.

Procedure steps

Step Action

1For an AC power supply, press the rocker switch located on the power supply to the on position ( ).

2On a DC power supply, ensure the DC power source is on.

3Verify that the power supply status LED for each power supply is green.

4Verify that the fan status LED is green.

5Verify that the air flows from the cooling fans through the vents of the chassis.

The fan tray red (fail) LED can illuminate briefly while the fans power to operational speed.

--End--

If status LEDs do not illuminate green, see Nortel Secure Router 4134 — Troubleshooting (NN47263-700).

Verifying a successful installation

Use the information in this section to verify that you have successfully installed the Secure Router 4134 and its components.

If any LED behavior indicates failure or is suspect, see Nortel Secure

Router 4134 — Troubleshooting (NN47263-700).

In a normal power-up sequence, the following events occur:

1.When you power up the router, the fans start and the Secure Router 4134 performs a self-test.

2.At the successful conclusion of the self-test sequence, LED activity begins. The following table describes LED behavior at power-up.

Nortel Secure Router 4134

Quick Start

NN47263-100 02.01 Standard

18 February 2008

Copyright © 2007, 2008 Nortel Networks

Image 52

Contents Quick Start Page Contents Introduction Power cord warning statement Copyright 2007, 2008 Nortel Networks International Regulatory Statements of Conformity FCC statement USA onlyTIA-968-A CE marking statement Europe only EN 55022 statementsEN 55024 statement EN 300386 statementBsmi statement Taiwan only Vcci statement Japan/Nippon onlyMIC notice Republic of Korea only National Safety Statements of Compliance EN 60950 statementNOM statement Mexico only Información NOM unicamente para MéxicoDenan statement Japan/Nippon only National Environmental Statements of ComplianceRoHS Directive Compliance Statement Safety messages Weee Directive Compliance StatementWarnung Warnung Hardware Notice Foreign Exchange Station FXS Interface Modules Risiko einer Augenverletzung durch LaserForeign Exchange Office FXO Interface Modules Personal safety and equipment protectionModule protection Cables and connectors protection Electrostatic dischargeAntistatic material Features Interface modulesNew in this release Introduction NavigationIntroduction Secure Router 4134 installation and initial configuration Secure Router 4134 installation and initial configuration Copyright 2007, 2008 Nortel Networks Secure Router 4134 installation and initial configuration Unpacking and inspecting the Secure Router 4134 chassis Step ActionInstalling a power supply module Secure Router 4134 accessories Accessory Function VerifiedInstalling the mounting brackets on the chassis PrerequisitesAverage time to install mounting brackets 2 minutes Prerequisites Installing the chassis Risk of injury Grounding the chassis Grounding the chassis Achtung Installing the interface modules Slot numbering legend printed on the Secure Router Installing a Small Module Foreign Exchange Office FXO Interface ModulesInstalling a Medium Module Installing a Large ModuleInstalling a Small Module in the Voice Carrier Medium Module Voice Carrier Medium Module slot numbering Prerequisites Connecting power cables Connecting AC power cablesConnecting DC power Average time to install one DC power cable 3 minutes Switch off the DC power source Copyright 2007, 2008 Nortel Networks End Powering up the router Verifying a successful installationLogon prompt appears on the console screen Copyright 2007, 2008 Nortel Networks Configuring the Secure Router 4134 for remote access Connecting a terminal for local accessEstablishing remote access Using SSH for remote access Login admin Password setupChanging the default administrator password EnableChanging the default administrator password Configuring the Secure Router 4134 for remote access Appendix Environmental requirements Environmental requirements Appendix Translations of safety messages Class a device caution statementQualified service personnel warning statement CuidadoOvercurrent warning statement AvisoCover plate warning statement Power cord warning statement Peligro Page Quick Start