Nortel Networks 4134 quick start Switch off the DC power source

Page 49

Connecting power cables 49

CAUTION

ACHTUNG

Stellen Sie als allgemeine Sicherheitsmaßnahme sicher, dass der Wechselstrom entweder durch eine Sicherung oder einen Wechselstromsicherung mit maximal 12 A fließt.

Prerequisites

•Ensure you have 18 AWG copper wire with appropriate terminal (lug). You require two wires for single source power, and four wires for redundant power supplies (that is, two wires for each input).

•Ensure you have a Phillips #2 screwdriver.

•Ensure you have a flathead screwdriver to tighten terminals.

DANGER

Ensure that you remove the proper amount of insulation from copper wires when you install the terminals (lugs). Ensure that no wires are exposed.

DANGER

GEFAHR

Stellen Sie sicher, dass Sie das richtige Maß an Isolierung von den Kupferkabeln entfernen, wenn Sie die Anschlüsse (Klemmen) installieren. Stellen Sie sicher, dass keine Kabel freiliegen.

Procedure steps

Step Action

1Switch off the DC power source.

DANGER

Before you continue with this procedure, ensure that the DC power source is switched off.

DANGER

GEFAHR

Bevor Sie dieses Verfahren fortsetzen, stellen Sie sicher, dass die Stromquelle für Wechselstrom ausgeschaltet ist.

2Loosen both terminal cover screws on the DC power supply, as shown in the following figure.

Nortel Secure Router 4134

Quick Start

NN47263-100 02.01 Standard

18 February 2008

Copyright © 2007, 2008 Nortel Networks

Image 49

Contents Quick Start Page Contents Introduction Power cord warning statement Copyright 2007, 2008 Nortel Networks FCC statement USA only International Regulatory Statements of ConformityCE marking statement Europe only EN 55022 statements TIA-968-AEN 300386 statement EN 55024 statementBsmi statement Taiwan only Vcci statement Japan/Nippon onlyMIC notice Republic of Korea only EN 60950 statement National Safety Statements of ComplianceNOM statement Mexico only Información NOM unicamente para MéxicoDenan statement Japan/Nippon only National Environmental Statements of ComplianceRoHS Directive Compliance Statement Weee Directive Compliance Statement Safety messagesWarnung Warnung Hardware Notice Risiko einer Augenverletzung durch Laser Foreign Exchange Station FXS Interface ModulesForeign Exchange Office FXO Interface Modules Personal safety and equipment protectionModule protection Electrostatic discharge Cables and connectors protectionAntistatic material Interface modules FeaturesNew in this release Navigation IntroductionIntroduction Secure Router 4134 installation and initial configuration Secure Router 4134 installation and initial configuration Copyright 2007, 2008 Nortel Networks Secure Router 4134 installation and initial configuration Step Action Unpacking and inspecting the Secure Router 4134 chassisSecure Router 4134 accessories Accessory Function Verified Installing a power supply modulePrerequisites Installing the mounting brackets on the chassisAverage time to install mounting brackets 2 minutes Prerequisites Installing the chassis Risk of injury Grounding the chassis Grounding the chassis Achtung Installing the interface modules Slot numbering legend printed on the Secure Router Foreign Exchange Office FXO Interface Modules Installing a Small ModuleInstalling a Large Module Installing a Medium ModuleInstalling a Small Module in the Voice Carrier Medium Module Voice Carrier Medium Module slot numbering Prerequisites Connecting AC power cables Connecting power cablesConnecting DC power Average time to install one DC power cable 3 minutes Switch off the DC power source Copyright 2007, 2008 Nortel Networks End Verifying a successful installation Powering up the routerLogon prompt appears on the console screen Copyright 2007, 2008 Nortel Networks Connecting a terminal for local access Configuring the Secure Router 4134 for remote accessEstablishing remote access Login admin Password setup Using SSH for remote accessEnable Changing the default administrator passwordChanging the default administrator password Configuring the Secure Router 4134 for remote access Appendix Environmental requirements Environmental requirements Class a device caution statement Appendix Translations of safety messagesCuidado Qualified service personnel warning statementAviso Overcurrent warning statementCover plate warning statement Power cord warning statement Peligro Page Quick Start