Nortel Networks 4134 quick start Installing a Medium Module, Installing a Large Module

Page 42

42Installing the Secure Router 4134 chassis and hardware components

4Push gently, but firmly, to seat the connector on the interface module in the chassis back panel.

5Use a Phillips screwdriver to tighten the two captive screws to secure the module to the chassis.

--End--

Installing a Medium Module

Use the procedure in this section to install a Medium Module in the Secure Router 4134. You can install Medium Modules in slots 5, 6, and 7.

ATTENTION

If you use a Voice Carrier Medium Module with the Secure Router 4134, Nortel recommends you install the Voice Carrier Medium Module in the chassis before installing Small Modules in the Voice Carrier Medium Module.

Procedure steps

Step Action

1Use a Phillips screwdriver to remove the slot cover plate from the slot in which you will install the module.

2Align the module with the slot and the slot module guides.

3Slide the module into the chassis until its connector panel touches the chassis back panel.

4Push gently, but firmly, to seat the connector on the interface module in the chassis back panel.

5Ensure the lever on the module is flush with the front panel of the Secure Router 4134.

6Use a Phillips screwdriver to tighten the two captive screws to secure the module to the chassis.

--End--

Installing a Large Module

Use the procedure in this section to install a Large Module in the Secure Router 4134. You can install a Large Module to span slots 6 and 7 only.

Procedure steps

Step Action

1Use a Phillips screwdriver to remove the slot cover plates from slots 6 and 7.

Nortel Secure Router 4134

Quick Start

NN47263-100 02.01 Standard

18 February 2008

Copyright © 2007, 2008 Nortel Networks

Image 42

Contents Quick Start Page Contents Introduction Power cord warning statement Copyright 2007, 2008 Nortel Networks International Regulatory Statements of Conformity FCC statement USA onlyTIA-968-A CE marking statement Europe only EN 55022 statementsEN 55024 statement EN 300386 statementVcci statement Japan/Nippon only Bsmi statement Taiwan onlyMIC notice Republic of Korea only NOM statement Mexico only National Safety Statements of ComplianceEN 60950 statement Información NOM unicamente para MéxicoNational Environmental Statements of Compliance Denan statement Japan/Nippon onlyRoHS Directive Compliance Statement Safety messages Weee Directive Compliance StatementWarnung Warnung Hardware Notice Foreign Exchange Station FXS Interface Modules Risiko einer Augenverletzung durch LaserPersonal safety and equipment protection Foreign Exchange Office FXO Interface ModulesModule protection Cables and connectors protection Electrostatic dischargeAntistatic material Features Interface modulesNew in this release Introduction NavigationIntroduction Secure Router 4134 installation and initial configuration Secure Router 4134 installation and initial configuration Copyright 2007, 2008 Nortel Networks Secure Router 4134 installation and initial configuration Unpacking and inspecting the Secure Router 4134 chassis Step ActionInstalling a power supply module Secure Router 4134 accessories Accessory Function VerifiedInstalling the mounting brackets on the chassis PrerequisitesAverage time to install mounting brackets 2 minutes Prerequisites Installing the chassis Risk of injury Grounding the chassis Grounding the chassis Achtung Installing the interface modules Slot numbering legend printed on the Secure Router Installing a Small Module Foreign Exchange Office FXO Interface ModulesInstalling a Medium Module Installing a Large ModuleInstalling a Small Module in the Voice Carrier Medium Module Voice Carrier Medium Module slot numbering Prerequisites Connecting power cables Connecting AC power cablesConnecting DC power Average time to install one DC power cable 3 minutes Switch off the DC power source Copyright 2007, 2008 Nortel Networks End Powering up the router Verifying a successful installationLogon prompt appears on the console screen Copyright 2007, 2008 Nortel Networks Configuring the Secure Router 4134 for remote access Connecting a terminal for local accessEstablishing remote access Using SSH for remote access Login admin Password setupChanging the default administrator password EnableChanging the default administrator password Configuring the Secure Router 4134 for remote access Appendix Environmental requirements Environmental requirements Appendix Translations of safety messages Class a device caution statementQualified service personnel warning statement CuidadoOvercurrent warning statement AvisoCover plate warning statement Power cord warning statement Peligro Page Quick Start