PARAMETER NAME/ | DESCRIPTION | DISPLAY SCREENS / | |
[MENU LOCATION] |
| DEFAULT SETTINGS | |
|
|
| |
Rectifier Description | Displays the model number of the installed | Rect 1 Desc | # |
{Status Only} | rectifier. NOTE: This information can be | MRF28H54 | |
[MODULES/RECT/INFO] | viewed for each rectifier installed by using the |
|
|
| horizontal arrow keys. |
|
|
Rectifier Fail | The output relay energized if Rectifier Fail | Rect 1ofN Almm+ | |
Security Level {1} | alarm occurs. This is a special rectifier alarm | Minor |
|
group that signifies that one rectifier has at least |
|
| |
| one alarm condition. |
|
|
Rectifier Fail | The output relay energized if Rectifier Fail | Rect 2ofN Almm+ | |
Security Level {1} | alarm occurs This is a special rectifier alarm group | Major |
|
that signifies that more than one rectifier has at |
|
| |
| least one alarm condition. |
|
|
Rectifier Fail Safe Voltage | Rectifier default output voltage if communication | Rect Fail Safem+ | |
Security Level {1} | with the control unit fails. |
| |
[MODULES/RECT/PARAM] |
|
|
|
Rectifier Fan Fail Alarm | The output relay that is energized or special | Rect FF Alm | m+ |
Security Level {1} | rectifier alarm group n of N that occurs when a | n of N |
|
| rectifier fan has failed. |
|
|
Rectifier Fan Fail Alarm Status | The status will be “ON” if the rectifier fan has | Rect 1 FF | # |
{Status Only} | failed. NOTE: This information can be viewed | OFF |
|
[MODULES/RECT/INFO] | for each rectifier installed by using the |
|
|
| horizontal arrow keys. |
|
|
Rectifier Fault Alarm (RFA) | The status will be on if the rectifier output has | Rect 1 RFA | # |
Status | failed. NOTE: This information can be viewed | OFF |
|
{Status Only} | for each rectifier installed by using the |
|
|
[MODULES/RECT/INFO] | horizontal arrow keys. |
|
|
Rectifier RFA Alarm | The output relay that is energized or special | Rect RFA Alm | m+ |
Security Level {1} | rectifier alarm group n of N that occurs when a | n of N |
|
| rectifier output has failed. |
|
|
Rectifier Standby Alarm | The output relay that is energized or special | Rect Stdby Almm+ | |
Security Level {1} | rectifier alarm group n of N that occurs when the | n of N |
|
| control unit is holding a rectifier in the standby |
|
|
| mode. |
|
|
Rectifier Standby Alarm Status | The status will be “ON” if the control unit is holding | Rect 1 Stdby | # |
{Status Only} | the rectifier in the standby mode. NOTE: This | OFF |
|
[MODULES/RECT/INFO] | information can be viewed for each rectifier |
|
|
| installed by using the horizontal arrow keys. |
|
|
Store Configuration | Setting this parameter to “Enable” will cause the | Store Cfg | m+ |
Security Level {1} | current rectifier configuration to be stored (the | Disable |
|
[SYSTEM/DIAG] | display toggles back to “Disable” after entry). |
|
|
System Current | The total system output current (calculated as the | Sys Current | + |
{Status Only} | sum of the individual rectifier output currents). | 145.8 | A |
[STATUS] |
|
|
|
System High Temperature | The output relay energized if the System | Sys HT Alm | m+ |
Alarm | Temperature exceeds the system high | Minor |
|
Security Level {1} | temperature threshold. |
|
|
|
|
| |
System High Temperature | System Temperature is ambient temperature | Sys HT Thr | m+ |
Threshold | measured inside the controller. An alarm will be | 70.0 | C |
Security Level {1} | reported if temperature is higher than the |
|
|
temperature entered. |
|
|
MX28B1200/2400 MX28B1200/4800 | Page 43 |