Siemens DataNET Hub (DNH) user manual Test Command Timeout Command

Page 89

Command Descriptions, Continued

“test” Command

“timeout” Command

This command places a selected port into a hardware diagnostic mode. The command

test 4

places port 4 into test mode. The hub will generate poll messages on port 4. All other ports continue to operate normally. The command

test off

turns off test mode. Only one port at a time may be in test mode.

This command may be used to disable the user login timeout. Normally, if a user has not issued a CLI command for five minutes, the hub-half will automatically shut down the user’s login session. This command may be used to defeat (and re-enable) this timeout:

timeout off	Disables timeout. The hub-half will not auto-
	matically log out the user, regardless of the time
	elapsed since the user last issued a CLI com-
	mand.
timeout on	Re-enables the five-minute CLI timer.

2000585-001

Command Summary • 81

Image 89

Contents December User’s Manual 2000585-001 Advance DataNET Hub DNHCopyright Notice Table of Contents Table of Contents Preface Audience & Purpose Chapter ContentsGetting Help Before You Call Technical SupportSafety Practices and Precautions Safety Practices and Precautions Description OverviewDual Hub Modules PortsAdvance Communi- cations System Package ConfigurationsEthernet Bridging DataNET Hub HierarchyDNH and Maxum Com Boards DataNET Hub OperationDNH Links Definitions DataNET SwitchingTransparency DataNET Hub Specifications DataNET Hub Specifications DataNET Hub Specifications Communication Cable Type Vendors & P/N Installation NotesComparisons DataNET CableDataNET Hub Specifications DataNET Hub Specifications Zone 1 Wall Mount Dimension Table Description Metric InchesZone 1 Wall Mount Dimension Table Page Introduction Installation OverviewDescription Receipt of DNH Unpacking Reporting Damage Unpacking and InspectionInstructions Package Configurations Wall Mounting Wall or Rack Mounting InstallationRack Mounting CE Installations Wiring Requirements Description Wiring of Power to DataNET HUB Site Wiring RequirementsRecommended DataNET Cable Cable Type Vendors & P/N Installation NotesDataNET Channels DataNET Fiber Optic Cable Connections Copper Wire Site RequirementsCE Installations NEC Div 2 or Non Hazardous Areas Ethernet Communica- tion Links CE Installation Kit Instructions CE InstallationsCE Installations Types of Connections Wiring ConnectionsBefore You Begin DNH Power Supply AC Power Mains ConnectionsInstallation Note Before You Begin Step ActionInstall 15-Ampere circuit breakers, disconnect switches or AC Power Mains Connections Description Hubs DataNET Copper ConnectionsPort Connections DataNET Ports+ Important Cable Impedance SettingsMaster Port Connectors TB15 TB18 Signal Equalizer Board Downlink Wiring withoutDescription Instructions DataNET Hub Signal Equalizer BoardRepeat the procedure for each connected port on the Hub Sample Calculations Equalizer Board SettingsRecommended Calculation OneExample Comparing SignalsOption 1. Connection Point Option 2. Connection Point View MeasurementsInstructions & Examples Step Action + 2.1 dB RX & TX Connections DataNET Fiber Optic ConnectionsDataNET Fiber Optic Coupler Fiber Optic Cable Type Port Connections Page Active Ethernet Port Ethernet ConnectionsPin No MDI Function 10BASE-T Cable RequirementsTasks Check Overview Command Line Definitions Important ChecklistIntroduction Chapter Preview Configuring Your PC Learning Hint Setting Network AddressConfiguring Your PC Click Terminal Settings button Configuring Your PC Getting Started Before You Begin Password ProtectionEstablishing a Connection How to Log Out Password FormatHow to Log On How to ChangeRemote Connection Log On At the prompt type login password IP AddressSetting Network Address Config address ip Assigning an IP Address IP Address How to Assign an IP AddressOverview Available IP AddressesFirmware Updates Click on Send Text File At the Local prompt type config address etherenetMAC Address Con- figuration Board Status LEDs Startup LED Status System Status LEDsAdvance DataNET Hub Communication boards have status LEDs For monitoring the DNH operationYellow Warn LED Blink Codes Red Fault LEDHub Port LEDs Green Normal LEDLED Ethernet Port LEDs Cross Link StatusCabling errors Example TroubleshootingConfiguration Conflicts Errors Configuration ParameterInstructions Signal Quality ProblemsTroubleshooting Description Unique Commands Command DescriptionsReset Password passwordTimeout on Timeout offConfig display Command Config netmask Command Config address ip command Config device id CommandConfig iproute Del Command Display Command Example local display links Display links CommandDownload Command Dn setuptime Events Command Dn CommandCommand Descriptions Dn module on dn module off Help Command List Command Command DescriptionLogin Command Examplelocal netstat dn clear Logout Command Netstat CommandPort Command Test Command Timeout Command Trace Command Validation timeout Command Captured frames Verbose CommandParts Catalog Overview How to Place an OrderPart Description Ordering Number Available PartsAvailable Parts