Siemens DataNET Hub (DNH) user manual Configuration Parameter, Errors

Page 74

Troubleshooting, Continued

Configuration Parameter

The device may have an invalid or duplicate device ID, IP address, Sub-

Errors:

net mask, or iproute.

 

 

Verify the configuration parameters by connecting a PC serial port to the

 

Configuration Port, logging in, and typing config display.

 

 

> login password

 

 

 

Applied Automation

 

 

 

Advance DataNET Hub

 

 

local> config display

 

 

 

Config:

 

 

 

 

type

DATANET HUB

 

 

address ip

 

172.16.99.7

 

 

subnetmask

255.255.0.0

 

 

address ethernet 00.c0.c9.01.20.a7

 

 

device ID

 

172.16.99.7

 

1

time server ip

0.0.0.0

 

2

 

 

 

 

3

 

 

 

Make sure each Hub half has a unique IP address and that both Hub halves have the same device ID. Usually the device ID is set to the IP address of the ‘A’ Hub.

Advance Network devices periodically broadcast their status for diagnos- tic and network routing purposes.

The Subnet mask must be identical on all Advance network devices (Maxum analyzer, NAU, ANCB, DNH), and connected to a single net- work, for the broadcast message to be received properly. If a remote de- vice does not show up in the device routing table, verify that the remote device matches the local device Subnet mask.

66 Data Communications Setup

2000585-001

Image 74
Contents Advance DataNET Hub DNH December User’s Manual 2000585-001Copyright Notice Table of Contents Table of Contents Audience & Purpose Chapter Contents PrefaceTechnical Support Getting Help Before You CallSafety Practices and Precautions Safety Practices and Precautions Dual Hub Modules OverviewDescription PortsPackage Configurations Advance Communi- cations SystemDataNET Hub Hierarchy Ethernet BridgingDNH and Maxum Com Boards DataNET Hub OperationDNH Links Definitions DataNET SwitchingTransparency DataNET Hub Specifications DataNET Hub Specifications DataNET Hub Specifications Comparisons Cable Type Vendors & P/N Installation NotesCommunication DataNET CableDataNET Hub Specifications DataNET Hub Specifications Dimension Table Description Metric Inches Zone 1 Wall MountZone 1 Wall Mount Dimension Table Page Installation Overview IntroductionUnpacking and Inspection Description Receipt of DNH Unpacking Reporting DamageWall or Rack Mounting Installation Instructions Package Configurations Wall MountingRack Mounting CE Installations Wiring Requirements Site Wiring Requirements Description Wiring of Power to DataNET HUBRecommended DataNET Cable Cable Type Vendors & P/N Installation NotesDataNET Channels DataNET Fiber Optic Cable Connections Copper Wire Site RequirementsCE Installations NEC Div 2 or Non Hazardous Areas Ethernet Communica- tion Links CE Installations CE Installation Kit InstructionsCE Installations Types of Connections Wiring ConnectionsBefore You Begin Installation Note Before You Begin AC Power Mains ConnectionsDNH Power Supply Step ActionInstall 15-Ampere circuit breakers, disconnect switches or AC Power Mains Connections DataNET Copper Connections Description HubsDataNET Ports Port ConnectionsCable Impedance Settings + ImportantMaster Port Connectors TB15 TB18 Downlink Wiring without Signal Equalizer BoardDataNET Hub Signal Equalizer Board Description InstructionsRepeat the procedure for each connected port on the Hub Recommended Equalizer Board SettingsSample Calculations Calculation OneComparing Signals ExampleView Measurements Option 1. Connection Point Option 2. Connection PointInstructions & Examples Step Action + 2.1 dB RX & TX Connections DataNET Fiber Optic ConnectionsDataNET Fiber Optic Coupler Fiber Optic Cable Type Port Connections Page Ethernet Connections Active Ethernet Port10BASE-T Cable Requirements Pin No MDI FunctionTasks Check Overview Command Line Definitions Important ChecklistIntroduction Chapter Preview Configuring Your PC Setting Network Address Learning HintConfiguring Your PC Click Terminal Settings button Configuring Your PC Getting Started Before You Begin Password ProtectionEstablishing a Connection How to Log On Password FormatHow to Log Out How to ChangeAt the prompt type login password IP Address Remote Connection Log OnSetting Network Address Config address ip Overview IP Address How to Assign an IP AddressAssigning an IP Address Available IP AddressesFirmware Updates Click on Send Text File At the Local prompt type config address etherenetMAC Address Con- figuration Advance DataNET Hub Communication boards have status LEDs System Status LEDsBoard Status LEDs Startup LED Status For monitoring the DNH operationHub Port LEDs Red Fault LEDYellow Warn LED Blink Codes Green Normal LEDEthernet Port LEDs Cross Link Status LEDCabling errors Example TroubleshootingConfiguration Conflicts Configuration Parameter ErrorsSignal Quality Problems InstructionsTroubleshooting Command Descriptions Description Unique CommandsTimeout on Password passwordReset Timeout offConfig address ip command Config device id Command Config display Command Config netmask CommandConfig iproute Del Command Display Command Example local display links Display links CommandDownload Command Events Command Dn Command Dn setuptimeCommand Descriptions Dn module on dn module off Command Description Help Command List CommandLogin Command Examplelocal netstat dn clear Logout Command Netstat CommandPort Command Test Command Timeout Command Trace Command Validation timeout Command Verbose Command Captured framesOverview How to Place an Order Parts CatalogAvailable Parts Part Description Ordering NumberAvailable Parts