Lightning Audio X1.1000.1D, X1.800.4, X1.400.2 manual Strapping Amplifiers X1.2000.1D Only

Page 11

Operation

STRAPPING AMPLIFIERS (X1.2000.1D Only)

The X1.2000.1D amplifiers have the ability to connect two together and have their outputs combined, or strapped, to power a single speaker load.

!CAUTION: Two X1.2000.1D amplifiers that are strapped together are not recommended for impedance loads below 2Ω.

1.Select which amplifier of the two will be the master. and set the Master/Slave switch in the "out" position.

NOTE: Only adjustments made to the master amplifier will effect the output to the connected speaker.

2.Connect RCA cables from the source signal to the input connection on the master amplifier.

3.Set the Master / Slave switch on the slave amplifier to the "in" position.

4.Connect a RCA cable from the MAS OUT connector on the master amplifier to the SLV IN connector on the slave amplifier.

5.Connect one of the negative (-) speaker outputs from the master amplifier to one of the negative (-) speaker outputs on the slave amplifier using a 10 gauge wire (minimum).

6.Connect one of the positive (+) speaker outputs from the master amplifier to the positive (+) terminal of the speaker being use.

7.Connect one of the positive (+) speaker outputs from the slave amplifier to the negative (-) terminal of the speaker being use.

11

Image 11

Contents Amplifier Introduction Table of ContentsX1.400.2 X1.800.4 Safety InstructionsDesign Features X1.1000.1D X1.2000.1DInstallation Considerations InstallationPassenger Compartment Mounting Battery and ChargingMounting Locations Engine CompartmentWiring the System X1.1000.1D Mono Amplifiers X1.1000.1D & X1.2000.1DChannel Set as 3-Channel Bridged Mounting Clip Mounting and installationX1.400.2 Channel Channel Bridged Speaker Impedance Using Passive CrossoversOperation Adjusting GainAdjusting Crossover X-OVER Strapping Amplifiers X1.2000.1D Only Symptom Diagnosis Remedy TroubleshootingSpecifications Ship to Electronics Limited Warranty InformationTable des matieres´ ’innovation ou la mortPratiquez UNE Écoute Sans Risquesmd Consignes de securite´ ´Particularites´ Techniques Considérations Concernant L’INSTALLATIONMontage dans l’habitacle Emplacements DE MontageBatterie ET Charge Compartiment moteurCblage DU Système X1.400.2 X1.1000.1D X1.800.4 X1.2000.1D Amplificateurs Mono X1.1000.1D et X1.2000.1DX1.800.4 Canaux Réglage en 3 canaux pontés Télécommande DEMontage et installation X1.400.2 Canaux Canaux pontésUtilisation DE Filtres Passifs Impédance de haut-parleurRéglage DU Filtre Passif RGL. Filtre FonctionnementRéglage DU Gain Jumelage DES Amplis X1.2000.1D seulement Caracteristiques´ Symptôme Diagnostic SolutionDepannage Garantie limitee´ ´indice de materias Introduccion´Caracteristicas´ de Diseeo´ Instrucciones de seguridadConsideraciones Sobre LA Instalación Instalacion´Batería Y Carga PrecauciónLugares DE Montaje Cableado DEL Sistema InstalacionPara impedancia de carga inferiores a Amplificadores Monofónicos X1.1000.1D & X1.2000.1DBajo Modelos X1.1000.1D & X1.2000.1D Solamente X1.400.2 Canales Canales con PuenteX1.800.4 Canales Control DE Nivel Remoto / EQ DEUsando X-OVERS Pasivos Impedancia del altavozAjuste DEL X-OVER Operacion´Ajuste DE LA Ganancia Puenteado DE Amplificadores Sólo X1.2000.1D Síntoma Diagnóstico Solución Solucion de ProblemasLightning Audio Informacion´ sobre la garantia´ limitadaEnviar a Electronics Inhaltsverzeichnis EinleitungDesigncharakteristiken SicherheitshinweiseEinbauüberlegungen EinbauBatterie UND Aufladung Von einem qualifizierten Lightning Audio Techniker einbauenBefestigungsstellen Verkabelung DES Systems Monoverstärker X1.1000.1D und X1.2000.1D Zweikanal überbrückt Einbau und InstallationZweikanal X1.400.2Verwendung VON Passiven Crossovern LautsprecherimpedanzCrossover Einstellen X-OVER BetriebLautstärke Gain Einstellen Zusammenschalten VON Verstärkern nur bei Modell X1.2000.1D Fehlerbeseitigung Symptom Diagnose MaßnahmeInformationen zur beschrAnkten¨ Garantie Indice IntroduzioneIstruzioni di Sicurezza Osservate LE Regole DEL Suono Senza PericoliCaratteristiche del Design InstallazioneConsiderazioni SULL’INSTALLAZIONE Montaggio nello scampartimento passeggeri Ubicazioni PER IL MontaggioBatteria E Caricamento Scompartimento del motoreAttenzione Cablaggio DEL SistemaAmplificatori Mono X1.1000.1D e X1.2000.1D Canali Impostare come 3 canali a ponte Montaggio ed installazioneX1.400.2 Canali ponti Come Usare LE Frequenze DI Incrocio Passive Impedenza dell’altoparlanteRegolazione Della Frequenza DI Incrocio X-OVER FunzionamentoRegolazione DI Guadagno Combinazione DI Amplificatori solo per il modello X1.2000.1D Sintomo Diagnosi Rimedio Individuazione/Riparazione GuastiInformazioni Inerenti alla Garanzia Limitata Italiano Page Lightning Audio