Lightning Audio X1.2000.1D, X1.800.4 manual Operation, Adjusting Gain, Adjusting Crossover X-OVER

Page 10

Operation

ADJUSTING GAIN

To adjust the gain setting, turn the amplifier gains all the way down. Turn the source unit volume up until distortion is audible and then turn it down a bit until the distortion is inaudible. This will be about two thirds all the way up on most source units. Next, turn the amplifier gain setting until once again distortion is audible and then back it down until the distortion is inaudible.

NOTE: For a more in depth setting procedure, contact Lightning Audio Technical Support.

ADJUSTING CROSSOVER (X-OVER)

Models X1.400.2 & X1.800.4

Placing the switch in the HPF position sets the amplifier to the High Pass mode, enabling frequencies above the cut-off point to pass, adjustable between 50-250Hz.

Placing the switch in the FLAT position sets the amplifier to the All Pass mode, preventing any crossover adjustment, allowing all frequencies to pass..

Placing the switch in the LPF position sets the amplifier to the Low Pass mode, enabling frequencies below the cut-off point to pass, adjustable between 50-250Hz.

Turn the crossover adjustment knob all the way down. With the system playing, turn the crossover adjustment knob up slowly until the desired crossover point is achieved.

Models X1.1000.1D & X1.2000.1D

Turn the crossover adjustment knob all the way down. With the system playing at normal listening level, turn the crossover adjustment knob up slowly until the desired crossover point is achieved.

SUBSONIC (Models X1.1000.1D & X1.2000.1D Only)

A high pass filter designed to prevent frequencies below the audio range from being applied to the subwoofer from the amplifier.

Set this to your personal preference while listening to the system.

PHASE (Models X1.1000.1D & X1.2000.1D Only)

This varies the inversion of the output signal from 0° to 180° from the input signal. Set this to your personal preference while listening to the system.

BASS EQ (Models X1.1000.1D & X1.2000.1D Only)

Used with the Remote Level/Bass EQ Control, the control will boost the frequency of what is set here.

Example: If the Bass EQ Freq on the amplifier is set to 50Hz, the Remote will boost that frequency.

Gain	Bass EQ Crossover

X1.1000.1D

X1.2000.1D is Simular

Subsonic Phase

Gain Crossover

X1.400.2

X1.800.4 is Simular

10

Image 10

Contents Amplifier Table of Contents IntroductionX1.1000.1D X1.2000.1D Safety InstructionsDesign Features X1.400.2 X1.800.4Installation Installation ConsiderationsEngine Compartment Battery and ChargingMounting Locations Passenger Compartment MountingWiring the System Mono Amplifiers X1.1000.1D & X1.2000.1D X1.1000.1DX1.400.2 Channel Channel Bridged Mounting and installationChannel Set as 3-Channel Bridged Mounting Clip Using Passive Crossovers Speaker ImpedanceAdjusting Crossover X-OVER Adjusting GainOperation Strapping Amplifiers X1.2000.1D Only Specifications TroubleshootingSymptom Diagnosis Remedy Limited Warranty Information Ship to Electronics’innovation ou la mort Table des matieres´Consignes de securite´ ´ Pratiquez UNE Écoute Sans RisquesmdConsidérations Concernant L’INSTALLATION Particularites´ TechniquesCompartiment moteur Emplacements DE MontageBatterie ET Charge Montage dans l’habitacleCblage DU Système Amplificateurs Mono X1.1000.1D et X1.2000.1D X1.400.2 X1.1000.1D X1.800.4 X1.2000.1DX1.400.2 Canaux Canaux pontés Télécommande DEMontage et installation X1.800.4 Canaux Réglage en 3 canaux pontésImpédance de haut-parleur Utilisation DE Filtres PassifsRéglage DU Gain FonctionnementRéglage DU Filtre Passif RGL. Filtre Jumelage DES Amplis X1.2000.1D seulement Depannage Symptôme Diagnostic SolutionCaracteristiques´ Garantie limitee´ Introduccion´ ´indice de materiasInstrucciones de seguridad Caracteristicas´ de Diseeo´Instalacion´ Consideraciones Sobre LA InstalaciónLugares DE Montaje PrecauciónBatería Y Carga Instalacion Cableado DEL SistemaAmplificadores Monofónicos X1.1000.1D & X1.2000.1D Para impedancia de carga inferiores aControl DE Nivel Remoto / EQ DE X1.400.2 Canales Canales con PuenteX1.800.4 Canales Bajo Modelos X1.1000.1D & X1.2000.1D SolamenteImpedancia del altavoz Usando X-OVERS PasivosAjuste DE LA Ganancia Operacion´Ajuste DEL X-OVER Puenteado DE Amplificadores Sólo X1.2000.1D Solucion de Problemas Síntoma Diagnóstico SoluciónEnviar a Electronics Informacion´ sobre la garantia´ limitadaLightning Audio Einleitung InhaltsverzeichnisSicherheitshinweise DesigncharakteristikenEinbau EinbauüberlegungenBefestigungsstellen Von einem qualifizierten Lightning Audio Techniker einbauenBatterie UND Aufladung Verkabelung DES Systems Monoverstärker X1.1000.1D und X1.2000.1D X1.400.2 Einbau und InstallationZweikanal Zweikanal überbrücktLautsprecherimpedanz Verwendung VON Passiven CrossovernLautstärke Gain Einstellen BetriebCrossover Einstellen X-OVER Zusammenschalten VON Verstärkern nur bei Modell X1.2000.1D Symptom Diagnose Maßnahme FehlerbeseitigungInformationen zur beschrAnkten¨ Garantie Introduzione IndiceOsservate LE Regole DEL Suono Senza Pericoli Istruzioni di SicurezzaConsiderazioni SULL’INSTALLAZIONE InstallazioneCaratteristiche del Design Scompartimento del motore Ubicazioni PER IL MontaggioBatteria E Caricamento Montaggio nello scampartimento passeggeriCablaggio DEL Sistema AttenzioneAmplificatori Mono X1.1000.1D e X1.2000.1D X1.400.2 Canali ponti Montaggio ed installazioneCanali Impostare come 3 canali a ponte Impedenza dell’altoparlante Come Usare LE Frequenze DI Incrocio PassiveRegolazione DI Guadagno FunzionamentoRegolazione Della Frequenza DI Incrocio X-OVER Combinazione DI Amplificatori solo per il modello X1.2000.1D Individuazione/Riparazione Guasti Sintomo Diagnosi RimedioInformazioni Inerenti alla Garanzia Limitata Italiano Page Lightning Audio