Samsung SF-560 manual Paper Specifications, Paper Storage Environment

Page 94

Paper Specifications

Category

Specifications

 

 

Acid Content

5.5 pH or lower

 

 

Caliper

0.094 ~ 0.18 mm (3.0 ~ 7.0 mils)

 

 

Curl in Ream

Flat within 5 mm (0.02 in.)

 

 

Cut Edge Conditions

Cut with sharp blades with no visible fray.

 

 

Fusing Compatibility

Must not scorch, melt, offset or release hazardous

 

emissions when heated to 200 °C (392 °F) for 0.1

 

second.

 

 

Grain

Long Grain

 

 

Moisture Content

4 % ~ 6 % by weight

 

 

Smoothness

100 ~ 400 Sheffied

 

 

Paper Storage Environment

Paper storage environmental conditions directly affect the feed operation.

Ideally, the machine and paper storage environment should be at or near room temperature, and not too dry or humid. Remember that paper is hygroscopic; it absorbs and loses moisture rapidly.

Heat works with humidity to damage paper. Heat causes the moisture in paper to evaporate, while cold causes it to condense on the sheets. Heating systems and air conditioners remove most of the humidity from a room. As paper is opened and used, it loses moisture, causing streaks and smudging. Humid weather or water coolers can cause the humidity to increase in a room. As paper is opened and used it absorbs any excess moisture, causing light print and dropouts. Also, as paper loses and gains moisture it can become distorted. This can cause paper jams.

Care should be taken not to purchase more paper than can be used in a short time (about 3 months). Paper stored for long periods may experience heat and moisture extremes, which can cause damage. Planning is important to prevent damage to large supplies of paper.

Unopened paper in sealed reams can remain stable for several months before use. Opened packages of paper have more potential for environment damage, especially if they are not wrapped with a moisture-proof barrier.

The paper storage environment should be properly maintained to ensure optimum performance. The required condition is 20 to 24 °C (68 to 75 °F), with a relative humidity of 45 % to 55 %. The following guidelines should be considered when evaluating the paper’s storage environment:

• Paper should be stored at or near room temperature.

• The air should not be too dry or too humid.

• The best way to store an opened ream of paper is to rewrap it tightly in its moisture-proof wrapping. If the machine environment is subject to extremes, unwrap only the amount of paper

to be used during the day’s operation to prevent unwanted moisture changes.

A

SPECIFICATIONS A.7

Page 93 Page 95
Image 94
Page 93 Page 95
Contents Page Page Contact Samsung World Wide Iii Contents Setting the Paper Type and Size for the Manual Feeder Changing Setting Options Advanced Fax Setting OptionsPaper Feeding Problems Copying Problems Faxing Problems Input Misfeed Exit MisfeedSafety and Regulatory Information Laser Safety Statement Power Saver Fax Branding Declaration of Conformity European Countries Replacing the Fitted Plug for UK Only Xiii Xiv Getting Started Unpacking TAM Lead for UK onlySelecting a Location Clearance SpaceRear View Understanding the Component LocationFront View These are the main components of your machineControl Panel Functions O P Y Starts a jobAttaching Accessories Document Output SupportHandset and Handset Cradle Installing the Toner Cartridge Loading Paper You can load approximately 250 sheetsChanging the Paper Size in the Paper Tray Connecting the Telephone Line Wall jackTurning the Machine On To view your display text in another language, see the nextSetting the Machine ID Changing the Display LanguageEntering Characters Using the Number Keypad Changing Numbers or Names Setting the Date and TimeKeypad Letters and Numbers Inserting a PauseChanging the Clock Mode Speaker Volume Setting SoundsSpeaker, Ringer, Key Sound and Alarm Sound You can control the following soundsToner Save Mode Using the Save ModesToll Save Mode Setting Up the Fax System Power Save ModeAvailable Fax Setup Options Basic Functions Preparing a Document Loading a DocumentDocuments printed using a dot-matrix printer Adjusting the Document ResolutionStandard Documents with normal-sized characters Fine Sending a Fax Automatically Sending a Fax ManuallyAutomatic Redialing Redialing the Last NumberConfirming Transmission To redial the number you last calledAbout Receiving Modes Loading Paper for Receiving FaxesReceiving Manually in Tel Mode Receiving Automatically in Fax ModeReceiving Automatically in Ans/Fax Mode Receiving Manually Using an Extension Telephone Receiving Faxes Using the Drpd ModeReceiving Faxes in the Memory Adjust the guide to the width of the print material Loading Paper for CopyingOpen the rear cover to use the rear output slot Making a CopyAfter copying, close the rear cover Setting Copy Options To clear the settings, use the Stop/Clear buttonChanging the Default Settings Reduced/Enlarged CopyingCollated Copy On Setting the Time Out OptionCollation Copying Press Start Copy/Fax to begin copyingPage Storing a Number for Speed Dialing Speed DialingPress Phone Book on the control panel Setting a Group Dial Number Group DialingEditing Group Dial Numbers Searching Sequentially through the Memory Press Enter when Search&Dial appears on the displaySearching for a Number in the Memory Searching with a Particular First LetterMemo Advanced FAX Functions Sending a Delayed Fax Sending Broadcasting FaxesAdvanced FAX Advanced FAX Advanced FAX To cancel your selection, press 2 to select No Canceling a Scheduled FaxAdding Documents to a Scheduled Fax Additional Features Using Secure Receiving Mode Printing Reports Changing Setting Options Using Advanced Fax SettingsPower Failure Report Printing a ReportAdvanced Fax Setting Options Remote fax machine to which faxes are forwarded RCV ForwardOption Description Maintenance Clearing the Memory Cleaning the Outside Adjusting ShadingCleaning Your Machine Cleaning the InsideCleaning the Scan Unit Disassemble the white roller as follows Saving Toner Maintaining the Toner CartridgeToner Cartridge Storage Expected Cartridge LifeCleaning the Drum Setting the Notify Toner OptionReplacing the Toner Cartridge Consumables and Replacement Parts Ignoring the Toner Empty MessageReplacing the ADF Rubber Pad Memo Troubleshooting Input Misfeed Clearing Document JamsExit Misfeed Paper Tray Clearing Paper JamsPaper Exit Area Fuser Area or Around the Toner Cartridge Manual Feeder Clearing LCD Error MessagesYour machine’s memory is full To cancel the fax job, press Tips for Avoiding Paper JamsInstalled Machine has a problem Please contact a serviceToner cartridge is not Install the toner cartridge. See Unit In. If the problem persists, pleasePaper No number assigned to it For storing a number, seePaper tray has run out Load paper in the paper tray. See You are doing in the AddSolving Problems Paper Feeding ProblemsCopying Problems Faxing ProblemsReferring to Receive your faxOther fax machine may be turned off, out of paper, or Specifications General Specifications Characters x 2 linesCopier Specifications Facsimile Specifications Data with ECM compression using only ITU-T No.1 ChartSupported Sizes of Paper Paper SpecificationsOverview Letter 215.9 x 279/8.5 x 138 to 146 g/m A4 210 x 297/8.27 xGuidelines for Using Paper Symptom Problem with Paper SolutionPaper Specifications Paper Storage EnvironmentSpecifications Index Page Rev
Top Page Image Contents