JVC TDR6 installation and operation guide TDEC-6161 Ports, Cabling the Analog Audio Connectors

Page 20

TDEC-6161The TDEC-6161 supports decoding of HDTV signals in either 1080i or 720p format. Video is output at 1.5 Gbps using the SDI interface.

The TDEC-6161 has two SDI ports, labeled SDI OUT 1 and SDI OUT 2.

SDI OUT 1

PUSH

HERE

SDI OUT 2

TDEC-6161

TDEC-6161 Ports

These two SDI ports provide identical serial digital bitstream outputs, using a 75Ω low-loss SDI cable. Both SDI OUT ports are BNC, 75Ω female connectors.

TDEC-6100The TDEC-6100 SDTV video and audio decoder module processes MPEG-2 4:2:2 Profile @ Main Level and Main Profile @ Main Level. Video may be output as composite analog NTSC or PAL or serial digital.

The module processes audio MPEG-2 Layer I or Layer II. Audio may be output as analog or AES/EBU digital stereo.

TDEC-6100 Ports

The TDEC-6100 ports are as follows:

COMPOSITE—outputs composite analog video on a female BNC 75Ω connector

D1—outputs digital video on a female BNC 75 Ω connector

ANALOG AUDIO A and B—output balanced analog audio on terminal block 30 Ω connectors which are factory selectable to 600 Ω

AES/EBU A and B—output balanced digital audio on male XLR 110 Ω connectors

Cabling the Analog Audio Connectors

The terminal block connectors consist of a row of detents on the top of the connector and a row of clamps on the bottom, as shown in the following graphic.

Detents

Clamps

10

01-0870-401B 01/03

Installing the TDR6

Image 20
Contents TDR6 Electric Shock Hazard Contents Chapter Configuring the TDR6 Chapter TroubleshootingAppendix F Option Module Overview Appendix G Demodulator Application NotesUsing This Guide PrefaceLocating Information Important InformationIssuing Commands Front Panel NavigationDisplays RevisionLCD Display ErrorsCartons and Packing Materials SAA IMQOVE MitiUse Approved Attachments Only Viii 01-0870-401B 01/03 Overview Overview Overview 01-0870-401B 01/03 Ventilation Installing the TDR6AC Power Cords Connecting to a Power Source Power-up SequenceBasic TDR6 SD Configuration with No Option Modules Installed Connecting to a Remote Unit TMAC-6125 PortsConnecting to a Network Cabling the Analog Audio Connectors TDEC-6161 PortsLNB Power Cabling the TDEM-611001-0870-401B 01/03 Front Panel TDR6 Front PanelTDR6 DTV Receiver/Decoder Menu Structure LCD Display LCD Symbols LCD Text FormatsData a Menu Qpsk Key Character Displayed Correcting Mistakes Example QPSK, 8PSK, 16QAM Command Description Parameters / Response ValuesDVB DetailsInputConfigFilter allows you set the PCR filter Message No services available BERPID NTSC, PAL, AutoMPEG-2 Value, that does not begin with Important Considerations when entering Biss Ekey EIDControlEIA-232 used to configure the remote port MACRestoring a Default Configuration Restoring a User ConfigurationSaving a User Configuration Locking the Front PanelSetting the Date Setting the TimePerforming a System Reset Unlocking the Front PanelRemote Port Using a Remote UnitConfiguring Remote Software Parameters Command Types Ethernet PortBaud 01-0870-401B 01/03 TDR6 HD/SD Back Panel with Remote Designators Error Messages Explanation Action Required Informational Remote Commands ResponseDelay AutoChannelmode LangSample Rate Source MPEG-2, Atsc MPEG2VOL BissBiss Mode Biss StatusDC Autosel DC FilterDclock DmlockEbno LNBFaultlogclear Hdvd DelayRolloff 35RCRO, 25RCRO TuneMC Access Code MC Access FP RO, RWMC Access Unlock MC Config ListMC Default Restore Pgca AuthorizationPgca Mode MC Ethernet IP AddressPgca Timeout DataHandshake InterfaceVD Delay VBIVBI Control VBI FormatVD Mode PAL, NTSC, Auto VD SetupVD PID VD SubmodeQuick Start Configuring the TDR6Configuration Selecting a Service Detailed TDR6 Configuration Setting Local Date and TimeTDR6 Detailed Configuration Procedure Demodulator ConfigurationConfiguring the L-Band Carrier Frequency Parameter Front Panel Menu Remote Command Qpsk01-0870-401B 01/03 Troubleshooting Fault Reporting and MonitoringCurrent Faults Fault HistoryCommand Mnemonics Abbreviation Option Module Fault Descriptors are defined in the following table Viewing Current Faults Viewing the Fault History LogInput Status LED Not Illuminated Minimum E b /N 0 dBPerformance Problems Technical Specifications FACTORY-CONFIGURABLE FeaturesStandard Features Default Configurations Demodulator a DStandard-Definition Video Decoder High-Definition Video DecoderUser Data a B Remote ControlAudio Decoder a F Front Panel Access Ethernet01-0870-401B 01/03 Fault Relay Port Pin Specifications Port PinoutsNumber Synchronous Asynchronous Ethernet Port Pin Assignments Signal Signal DefinitionUser Data port Pin Specifications Standard RS232 Port Specifications TMAC-6125 SpecificationsTAUD-6100 Specifications TDEC-6100 SpecificationsTDEC-6161 Specifications TDEM-6110 Specifications LNB Port Specifications01-0870-401B 01/03 Tiernan VBI Data Transmission PALTiernan VBI Data Transmission Tiernan CC Mode is for Ntsc Format Only Tiernan Proprietary Closed Captions Tiernan CCDVB 422 Expanded Windows, 16-line and 32-line Lines Expanded Windows Field for an Encoded Picture Frame Front Panel Commands for Encoder Configuration Tiernan Closed Captions Front Panel CommandsRemote Commands for Encoder Configuration VE TCCVE Vbipass 32LINES01-0870-401B 01/03 Option Module Overview Typical Option ModuleOption Module Overview Demodulator Tuner SAW Filter Demodulator Application NotesIndustry Standard LNB Frequencies Information Rate SpacingOutput Spectrum Width Eb/N0 DefinitionMinimum and Maximum Information Rates TransponderEstimating Eb/N0 Using a Spectrum Analyzer Demodulator Low Eb/N0 AlarmEb/N0 Estimation Algorithm Spectrum AnalyzerDiagnostic Commands Offset = Actual RF Programmed RF Table Top and Rack Mount Installation Instructions Rear Rack Mount Instructions Rear Rack Bracket Mounting Instructions Fuse01-0870-401B 01/03 Index Index