JVC TDR6 installation and operation guide Value, that does not begin with

Command	Description		Parameters / Response Values
Handshake	Sets the handshaking parameter for the user data port.	■ On: Enables handshaking for the specified
			user data port
		■ Off: Disables handshaking for the specified
			user data port
Config Mode	Setting determines how the user data parameters are set.	■ Auto: TDR6 automatically configures the user
			data parameters to match those of the
			incoming transport stream
		■ Manual: all user data parameters must be
			manually set by the operator
Baud	Sets the baud rate for the data channel	■ Asynchronous: 1200, 2400, 4800, 9600,
			19200, 38400
		■	Synchronous: 0 - 4.096 Mbps
Data Bits	Sets the character length for the asynchronous data channel	7, 8
Parity	Sets the parity for the asynchronous data channel	None, Even, Odd
Stop Bits	Sets the number of stop bits for asynchronous data channel	1, 2
Details>VBI>Format: used to set the VBI parameters; for additional information on VBI, refer to the appendix on VBI data
transmission.
VBI Format	When VBI Fmt Cntrl is set to Auto, this parameter is query-only;	■ Off – no VBI information will be included in the
	the TDR6 automatically detects and processes the incoming VBI		video output stream
	data.		Note: VBI Fmt Cntrl must be set to manual for
	When VBI Fmt Cntrl is set to Manual, this parameter is used to		this parameter to be set to off.
	set the type of VBI format to be decoded and included in the	■ TiernanCC – sets the VBI format to Tiernan
	video output stream.		proprietary closed captions
		■ Lines16 – sets the VBI format to expanded
			windows, 16 lines
		■ Lines32 – sets the VBI format to expanded
			windows, 32 lines
VBI Fmt Cntrl	Setting determines if the TDR6 will automatically detect, decode,	■ Auto – the TDR6 automatically determines the
	and include the VBI data in the output stream, or if the user will		type of incoming VBI data, decodes it and
	manually set all parameters.		includes it in the output stream
		■ Manual – enables you to manually set the VBI
			format to be decoded and included in the
			video output stream.
Details>PGCA: queries the protection and authorization status of a signal
Status	Query-only; displays if the selected service is PGCA protected	■	PGCA_Enabled
		■	In_the_Clear

Details>BISS: used to set the BISS mode and associated key and ID values. The key and ID values should be obtained from the site operator who has set-up the encryption at the encoder site.

The front panel numeric keypad has been enhanced to provide alpha-numeric entries for the 1KEY, EKEY, and EID parameter entries. For additional information on alpha-numeric entries, refer to the appropriate section in this supplement.

Status	Query-only; displays the state of the incoming transport stream.	■ Scrambled: the incoming transport stream is
		scrambled
		■ Not_scrambled: the incoming transport stream
		is not scrambled
1Key	Sets the key value for BISS 1 mode. The 1Key value is also	■ The value is a 12 character hexadecimal
	referred to as the clear session word.	value, that does not begin with 0x
	Important Considerations when entering BISS 1KEY:	■ If less than 12 characters are entered, the
	■ This command must be set before BISS Mode1 is set.	TDR6 will not set the command.
	■ This command may not be entered/changed more than 10	■ If more than 12 characters are entered, the
	times within a five minute time period.	TDR6 truncates the value to the first 12
	■ When re-entering/changing this command, there must be at	characters entered.
	least a 10 second time delay between entries.
	■ The value cannot begin with the hex values 0x
	The value cannot be displayed once it is entered. Instead, the
	TDR6 will display 12 asterisks.

26 01-0870-401B 01/03 Front Panel