JVC TDR6 installation and operation guide Ber, Message No services available

Command	Description	Parameters / Response Values
Raw BER	Query-only; displays the raw bit error rate; this rate is the error	—
	rate of the signal as it is received from the satellite, before error
	correction is applied.
BER	Query-only; displays the bit error rate; this value represents the	—
	number of errors detected in the signal after error correction is
	applied. This rate should be a zero for correct performance.
Rx Level	Query-only; displays the power level of the input signal.	value in .dBm
Peak Jitter	Query-only; displays the difference, or jitter, between the STC	value in ns
	and PCR clocks.

Details>Input>Status>ASI: allows you to query the presence of the ASI signal, as well as other transport stream parameters

Signal	Query-only; displays if the ASI signal is present or not	Present, Absent
	Note: Signal is only available when
	Details>Input>Config>Select>Input is set to ASI.
Transport	Query-only; displays the lock status of the transport stream	Locked, Unlocked
Rate	Query-only; displays the output rate for the QPSK demodulator	value in bps
Peak Jitter	Query-only; displays the difference, or jitter, between the STC	value in ns
	and PCR clocks.

Details>Service: consists of two submenus, Number and Auto Select, which enable you to query and select the services available in the transport stream.

Once you have selected a service, the Video Decoder, Audio Decoder, and User Data menus display the PIDs available for the selected service.

Number	Selects a service from those available in the transport stream.	Displays a list of available services.
	Once a service is selected, the TDR6 processes that service	■ Each available service in the transport stream
	until:	consists of a program number, a service
	■ Another service is selected	name, and a service provider.
	or	■ If the transport stream does not contain
	■ The selected service is no longer available in the transport	service names and providers, only the
	stream	program numbers are displayed.
		■ If the transport stream input is not connected,
		or if it lacks PSI information, the LCD displays
		the message: No services available.
Auto Select	Determines which service, including audio and data services,	■ On – when Auto Select is set to On, the TDR6
	that the TDR6 will select when any of the following events occur:	automatically selects the first available service
	■ The TDR6 power is turned off and then restored, or the unit is	in the transport stream.
	reset	Note: If you change the Auto Select function to
	■ The TDR6 loses and then re-establishes lock on the transport	On after you have selected a service, the
	stream	TDR6 will continue to process the service you
	Note: Since the typical SCPC transmission consists of a single	selected until one of the events occurs, then
		the TDR6 selects the first available service in
	service that includes of a single video/audio pair, the Auto Select
		the transport stream.
	feature was added to simplify the configuration process for
		■ Off – when Auto Select function is set to Off,
	typical SCPC users. When the Auto Select feature is enabled, or
	set to On, the decoder automatically selects the service with the	the TDR6 searches the transport stream for
	lowest service number first, then selects the video component	the last service you manually selected.
	with the lowest PID, and finally selects the audio components	If the service is found in the transport stream,
	with the lowest PIDS for audio A/B.	the TDR6 selects the service, and the LCD
	With Auto Select set to Off, the decoder can be configured to	displays the program number, service name,
	process a particular service, and within that service, to process	and service provider.
	selected video and audio services.	If the service is not found in the transport
		stream, the LCD displays Service Not
		Available, the TDR6 does not select a service,
		and no video, audio, or user data will be
		output.

Front Panel 01-0870-401B 01/03 23