JVC TDR6 installation and operation guide Rear Rack Mount Instructions

Page 98

2.Attach the brackets to both sides of the unit:

a.Line up the small holes on the bracket with the unit’s mounting holes, which are located towards the front of each side panel.

b.Thread all of the screws through the bracket’s small holes and into the Tiernan unit. The screws should be flush with the bracket when tightened.

Front Bracket

Front Bracket

3.Mount the unit in the rack by attaching the front brackets to the rack using your own washers and bolts.

4.Ensure that the installation provides the minimum required air flow clearances at the sides and rear of the unit.

The TDR6 is not designed to be installed with rack-mount slides.

NOTE

Rear Rack Mount Instructions

The rear rack mount kit contains the following items:

■Two mounting plates

■Two rack mount brackets

■Four mounting plate screws

■Four connector screws with attached washers. Note: the 1U ship kit contains eight connector screws.

■Four rack mount bracket screws with attached washers

mounting	rack mount
plates	brackets

connector screws with washers

Note: 1U kit contains eight connector screws

mounting plate screws

rack mount bracket screws

with washers

88

01-0870-401B 01/03

Table Top and Rack Mount Installation Instructions

Image 98

Contents TDR6 Electric Shock Hazard Contents Appendix F Option Module Overview Chapter Configuring the TDR6Chapter Troubleshooting Appendix G Demodulator Application NotesLocating Information Using This GuidePreface Important InformationDisplays Issuing CommandsFront Panel Navigation RevisionLCD Display ErrorsCartons and Packing Materials OVE SAAIMQ MitiUse Approved Attachments Only Viii 01-0870-401B 01/03 Overview Overview Overview 01-0870-401B 01/03 Ventilation Installing the TDR6AC Power Cords Connecting to a Power Source Power-up SequenceBasic TDR6 SD Configuration with No Option Modules Installed Connecting to a Remote Unit TMAC-6125 PortsConnecting to a Network Cabling the Analog Audio Connectors TDEC-6161 PortsLNB Power Cabling the TDEM-611001-0870-401B 01/03 Front Panel TDR6 Front PanelTDR6 DTV Receiver/Decoder Menu Structure LCD Display LCD Symbols LCD Text FormatsData a Menu Qpsk Key Character Displayed Correcting Mistakes Example QPSK, 8PSK, 16QAM Command Description Parameters / Response ValuesDVB DetailsInputConfigFilter allows you set the PCR filter Message No services available BERPID NTSC, PAL, AutoMPEG-2 Value, that does not begin with Important Considerations when entering Biss Ekey EIDControlEIA-232 used to configure the remote port MACSaving a User Configuration Restoring a Default ConfigurationRestoring a User Configuration Locking the Front PanelPerforming a System Reset Setting the DateSetting the Time Unlocking the Front PanelRemote Port Using a Remote UnitConfiguring Remote Software Parameters Command Types Ethernet PortBaud 01-0870-401B 01/03 TDR6 HD/SD Back Panel with Remote Designators Error Messages Explanation Action Required Informational Remote Commands ResponseChannelmode DelayAuto LangVOL Sample RateSource MPEG-2, Atsc MPEG2 BissDC Autosel Biss ModeBiss Status DC FilterEbno DclockDmlock LNBRolloff 35RCRO, 25RCRO FaultlogclearHdvd Delay TuneMC Access Unlock MC Access CodeMC Access FP RO, RW MC Config ListPgca Mode MC Default RestorePgca Authorization MC Ethernet IP AddressHandshake Pgca TimeoutData InterfaceVBI Control VD DelayVBI VBI FormatVD PID VD Mode PAL, NTSC, AutoVD Setup VD SubmodeQuick Start Configuring the TDR6Configuration Selecting a Service TDR6 Detailed Configuration Procedure Detailed TDR6 ConfigurationSetting Local Date and Time Demodulator ConfigurationConfiguring the L-Band Carrier Frequency Parameter Front Panel Menu Remote Command Qpsk01-0870-401B 01/03 Current Faults TroubleshootingFault Reporting and Monitoring Fault HistoryCommand Mnemonics Abbreviation Option Module Fault Descriptors are defined in the following table Viewing Current Faults Viewing the Fault History LogInput Status LED Not Illuminated Minimum E b /N 0 dBPerformance Problems Technical Specifications FACTORY-CONFIGURABLE FeaturesStandard Features Standard-Definition Video Decoder Default ConfigurationsDemodulator a D High-Definition Video DecoderUser Data a B Remote ControlAudio Decoder a F Front Panel Access Ethernet01-0870-401B 01/03 Fault Relay Port Pin Specifications Port PinoutsNumber Synchronous Asynchronous Ethernet Port Pin Assignments Signal Signal DefinitionUser Data port Pin Specifications Standard RS232 Port Specifications TMAC-6125 SpecificationsTAUD-6100 Specifications TDEC-6100 SpecificationsTDEC-6161 Specifications TDEM-6110 Specifications LNB Port Specifications01-0870-401B 01/03 Tiernan VBI Data Transmission PALTiernan VBI Data Transmission Tiernan CC Mode is for Ntsc Format Only Tiernan Proprietary Closed Captions Tiernan CCDVB 422 Expanded Windows, 16-line and 32-line Lines Expanded Windows Field for an Encoded Picture Frame Front Panel Commands for Encoder Configuration Tiernan Closed Captions Front Panel CommandsVE Vbipass Remote Commands for Encoder ConfigurationVE TCC 32LINES01-0870-401B 01/03 Option Module Overview Typical Option ModuleOption Module Overview Demodulator Tuner SAW Filter Demodulator Application NotesIndustry Standard LNB Frequencies Information Rate SpacingMinimum and Maximum Information Rates Output Spectrum WidthEb/N0 Definition TransponderEb/N0 Estimation Algorithm Estimating Eb/N0 Using a Spectrum AnalyzerDemodulator Low Eb/N0 Alarm Spectrum AnalyzerDiagnostic Commands Offset = Actual RF Programmed RF Table Top and Rack Mount Installation Instructions Rear Rack Mount Instructions Rear Rack Bracket Mounting Instructions Fuse01-0870-401B 01/03 Index Index