JVC TDR6 Unlocking the Front Panel, Setting the Date, Setting the Time, Performing a System Reset

Page 40

Unlocking the Front Panel

To unlock the front panel:

1.From the DTV Receiver/Decoder menu, select Control. The Control menu displays.

2.Select FP_Lock. The Front Panel Access menu displays showing the status of the front panel: Password = 0.

3.Using the front panel keypad, type in the password and press Enter. The default password is 7384.

4.The front panel displays State = Unlocked indicating that the front panel is now unlocked.

If the wrong password is entered, the TDR6 displays Password = 0. If this occurs, use the front panel keypad to type in the correct password and press Enter.

Setting the Date

To set the date:

1.From the DTV Receiver/Decoder menu, select Control. The Control menu displays.

2.Select Clock>Date.

3.Use the keypad to type in the correct date, separating each category with a decimal point. The date is entered in mm/dd/yyyy format.

4.Press the Enter button.

If the date is entered incorrectly, or an out-of-range value is entered, the TDR6 will display and continue to use the previously set date.

Setting the Time

The hours are in a 24-hour format and must be set from 00 to 23, where 00 is midnight and 23 is 11 PM. For example, for 8 AM you would set the hours to 08, and for 8 PM you would set the hours to 20. Both minutes and seconds can be set from 00 to 59. To set the time:

1.From the DTV Receiver/Decoder menu, select Control. The Control menu displays.

2.Select Clock>Time.

3.Use the keypad to type in the correct hour, minutes, and seconds, separating each category with a period.

4.Press Enter.

Performing a System Reset

To reset the TDR6:

1.From the DTV Receiver/Decoder menu, select Control. The Control menu displays.

2.Select Reset and press Enter. The TDR6 is reset to the last configuration set; all programmable logic and firmware is reloaded; the unit is restarted; and the fault history log is cleared

30

01-0870-401B 01/03

Front Panel

Image 40
Contents TDR6 Electric Shock Hazard Contents Chapter Configuring the TDR6 Chapter TroubleshootingAppendix F Option Module Overview Appendix G Demodulator Application NotesUsing This Guide PrefaceLocating Information Important InformationIssuing Commands Front Panel NavigationDisplays RevisionCartons and Packing Materials ErrorsLCD Display SAA IMQOVE MitiUse Approved Attachments Only Viii 01-0870-401B 01/03 Overview Overview Overview 01-0870-401B 01/03 AC Power Cords Installing the TDR6Ventilation Connecting to a Power Source Power-up SequenceBasic TDR6 SD Configuration with No Option Modules Installed Connecting to a Remote Unit TMAC-6125 PortsConnecting to a Network Cabling the Analog Audio Connectors TDEC-6161 PortsLNB Power Cabling the TDEM-611001-0870-401B 01/03 Front Panel TDR6 Front PanelTDR6 DTV Receiver/Decoder Menu Structure LCD Display LCD Symbols LCD Text FormatsData a Menu Qpsk Key Character Displayed Correcting Mistakes Example DVB Command Description Parameters / Response ValuesQPSK, 8PSK, 16QAM DetailsInputConfigFilter allows you set the PCR filter Message No services available BERPID NTSC, PAL, AutoMPEG-2 Value, that does not begin with Important Considerations when entering Biss Ekey EIDControlEIA-232 used to configure the remote port MACRestoring a Default Configuration Restoring a User ConfigurationSaving a User Configuration Locking the Front PanelSetting the Date Setting the TimePerforming a System Reset Unlocking the Front PanelConfiguring Remote Software Parameters Using a Remote UnitRemote Port Command Types Ethernet PortBaud 01-0870-401B 01/03 TDR6 HD/SD Back Panel with Remote Designators Error Messages Explanation Action Required Informational Remote Commands ResponseDelay AutoChannelmode LangSample Rate Source MPEG-2, Atsc MPEG2VOL BissBiss Mode Biss StatusDC Autosel DC FilterDclock DmlockEbno LNBFaultlogclear Hdvd DelayRolloff 35RCRO, 25RCRO TuneMC Access Code MC Access FP RO, RWMC Access Unlock MC Config ListMC Default Restore Pgca AuthorizationPgca Mode MC Ethernet IP AddressPgca Timeout DataHandshake InterfaceVD Delay VBIVBI Control VBI FormatVD Mode PAL, NTSC, Auto VD SetupVD PID VD SubmodeConfiguration Configuring the TDR6Quick Start Selecting a Service Detailed TDR6 Configuration Setting Local Date and TimeTDR6 Detailed Configuration Procedure Demodulator ConfigurationConfiguring the L-Band Carrier Frequency Parameter Front Panel Menu Remote Command Qpsk01-0870-401B 01/03 Troubleshooting Fault Reporting and MonitoringCurrent Faults Fault HistoryCommand Mnemonics Abbreviation Option Module Fault Descriptors are defined in the following table Viewing Current Faults Viewing the Fault History LogInput Status LED Not Illuminated Minimum E b /N 0 dBPerformance Problems Technical Specifications FACTORY-CONFIGURABLE FeaturesStandard Features Default Configurations Demodulator a DStandard-Definition Video Decoder High-Definition Video DecoderAudio Decoder a F Remote ControlUser Data a B Front Panel Access Ethernet01-0870-401B 01/03 Fault Relay Port Pin Specifications Port PinoutsUser Data port Pin Specifications Standard RS232 Ethernet Port Pin Assignments Signal Signal DefinitionNumber Synchronous Asynchronous Port Specifications TMAC-6125 SpecificationsTDEC-6161 Specifications TDEC-6100 SpecificationsTAUD-6100 Specifications TDEM-6110 Specifications LNB Port Specifications01-0870-401B 01/03 Tiernan VBI Data Transmission PALTiernan VBI Data Transmission Tiernan CC Mode is for Ntsc Format Only Tiernan Proprietary Closed Captions Tiernan CCDVB 422 Expanded Windows, 16-line and 32-line Lines Expanded Windows Field for an Encoded Picture Frame Front Panel Commands for Encoder Configuration Tiernan Closed Captions Front Panel CommandsRemote Commands for Encoder Configuration VE TCCVE Vbipass 32LINES01-0870-401B 01/03 Option Module Overview Typical Option ModuleOption Module Overview Industry Standard LNB Frequencies Demodulator Application NotesDemodulator Tuner SAW Filter Information Rate SpacingOutput Spectrum Width Eb/N0 DefinitionMinimum and Maximum Information Rates TransponderEstimating Eb/N0 Using a Spectrum Analyzer Demodulator Low Eb/N0 AlarmEb/N0 Estimation Algorithm Spectrum AnalyzerDiagnostic Commands Offset = Actual RF Programmed RF Table Top and Rack Mount Installation Instructions Rear Rack Mount Instructions Rear Rack Bracket Mounting Instructions Fuse01-0870-401B 01/03 Index Index