TDR6 Remote Command Listing (continued)
Mnemonics | Parameters/ | DVB Defaults |
| Description |
Response Values |
| |||
|
|
|
| |
|
|
|
|
|
MC DEFAULT RESTORE | where <string> = DVB, | — |
| Resets the TDR6 with the specified |
<string> | Default1, Default2, and |
|
| configuration. |
| Default3 |
|
| For more information on configurations, refer to the |
|
|
|
| configuration chapter. |
|
|
|
| Front panel equivalent: Config>Default>Restore |
|
|
|
|
|
MC ETHERNET IP ADDRESS | <x.x.x.x> where each x | — |
| Sets the ethernet IP address for the TDR6. Example: |
| represents a decimal |
|
| 192.200.9.201 |
| number from 0 to 255 |
|
| Front panel equivalent: Control>Network>Address |
|
|
|
|
|
MC ETHERNET IP | <x.x.x.x> where each x | 0.0.0.0 |
| Sets the IP gateway address. |
GATEWAY | represents a decimal |
|
| Front panel equivalent: Control>Network>Gateway |
| number from 0 to 255 |
|
|
|
|
|
|
|
|
MC ETHERNET IP MAC | Format: | — |
| Sets the Ethernet hardware address. |
| <xx:xx:xx:xx:xx:xx> |
|
| For example: 00:e0:74:00:02:cb |
| where xx is a |
|
|
|
| hexadecimal number |
|
|
|
| from 0 to f. |
|
|
|
|
|
|
| |
MC ETHERNET IP MASK | <x.x.x.x> where each x | 255.255.255.0 | Sets the IP address mask (IP subnet mask). | |
| represents a decimal |
|
| Front panel equivalent: Control>Network>Mask |
| number from 0 to 255 |
|
|
|
|
|
|
|
|
MC HW OPTS | — | — |
| |
|
|
|
| controller card. |
|
|
|
| Front panel equivalent: None |
|
|
|
|
|
MC HW TYPE | — | — |
| |
|
|
|
| Front panel equivalent: None |
|
|
|
|
|
MC RS232 BAUD | 1200, 2400, 4800, 9600, | 38400 |
| Sets the baud rate for the remote port. |
| 19200, 38400 |
|
| Front panel equivalent: |
|
|
|
|
|
MC RS232 DATA | 7, 8 | 8 |
| Sets the data bits for the remote port. |
|
|
|
| Front panel equivalent: |
|
|
|
|
|
MC RS232 HARDFLOW | On, Off | On |
| ■ On: sets data flow to be controlled by hardware |
|
|
|
| ■ Off: permits data flow to be controlled by hardware |
|
|
|
| Front panel equivalent: |
|
|
|
|
|
MC RS232 PARITY | None, Odd, Even | None |
| Sets the parity for the remote port. |
|
|
|
| Front panel equivalent: |
|
|
|
|
|
MC RS232 SOFTFLOW | On, Off | Off |
| ■ On: sets data flow to be controlled by software |
|
|
|
| ■ Off: permits data flow to be controlled by software |
|
|
|
| Front panel equivalent: |
|
|
|
|
|
MC RS232 STOP | 1, 2 | 1 |
| Sets the stop bits for the remote port. |
|
|
|
| Front panel equivalent: |
|
|
|
|
|
MC SW | — | — |
| |
|
|
|
| Front panel equivalent: Version |
|
|
|
|
|
PGCA | — | — |
| When PGCA is entered, the TDR6 returns the following |
|
|
|
| conditional access information: mode, status, authorization, |
|
|
|
| and |
|
|
|
| Front panel equivalent: None |
|
|
|
|
|
PGCA AUTHORIZATION | Yes, No, N/A | — |
| |
|
|
|
| has authorized your TDR6 to receive the selected service. |
|
|
|
| Front panel equivalent: Details>PGCA>Authorization |
|
|
|
|
|
PGCA MODE | Auto | Auto |
| Sets the TDR6 to automatically receive authorized PGCA- |
|
|
|
| protected signals. |
|
|
|
| Front panel equivalent: None |
|
|
|
|
|
PGCA STATUS | In_the_Clear, | — |
| |
| PGCA_Enabled |
|
| protected. |
|
|
|
| Front panel equivalent: Details>PGCA>Status |
|
|
|
|
|
Using a Remote Unit |
| 43 |