JVC RX-DV31 manual Sound Adjustments, Press Adjust, Front speaker output balance

Sound Adjustments

You can make sound adjustments to your preference after completing basic setting.

Adjustment items:

•Front speaker output balance*1

•Tone*1

•Speaker output levels*1

•DAP effect level

•Subwoofer audio position

7Operating procedure

Ex.: When setting the front speaker output balance.

Before you start, remember...

There is a time limit in doing the following steps.

If the setting is canceled before you finish, start from step 1 again.

1Press ADJUST.

English

*1 You can also make these adjustments using the Choice menu (see pages 53 to 58).

Note:

•Adjustments you made are memorized separately for each source.

7Operation buttons

On the front panel ONLY*2

Button	To do
ADJUST	Show the adjustable items on the

display*3.

CONTROL 5/∞ Select an item on the display. Each time you press the button, the adjustable items change (see “Configuration of the items on the display” below).

CONTROL 3/2 Adjust the selected item.

•When no operation is done for about 5 seconds, the indications on the display will disappear.

*2 You can also make sound adjustment except for front speakers’ output balance from the remote control.

*3 Pressing ADJUST repeatedly also changes the items.

Configuration of the items on the display

BAL	BASS	TREBLE
(Balance)
SUBWFR*4	CENTER*4	SURR L*4
(Subwoofer)		(Surround left)

The CONTROL buttons now work for sound adjustments. The setting item selected previously appears on the display.

2Press CONTROL ∞ (or 5) repeatedly until “BAL (Balance)” (with the current setting) appears on the display.

ANALOG DIGITAL AUTO		PL DSP SLEEP PROGRAM REPEAT 1A-B RANDOM PROGRESSIVE RDS	TA NEWS INFO	INPUT ATT
PPCM AUTO SURROUND				SPK 1	2 RE	C
DIGITAL L C	R	GROUP TITLE TRACK CHAP. RESUME B.S.P BONUS TUNED STEREO	AUTO MUTING	AUTO	MODE
				A.POSITION

LPCM SUBWFR LFE	kHz
MPEG-2 AAC LS S RS	MHz
	VOL

3Press CONTROL 3 (or 2) to adjust the front speaker balance.

•Each time you press the button, the indication changes as follows:

ANALOG DIGITAL AUTO		PL DSP SLEEP PROGRAM REPEAT 1A-B RANDOM PROGRESSIVE RDS	TA NEWS INFO	INPUT ATT
PPCM AUTO SURROUND				SPK 1	2 RE	C
DIGITAL L C	R	GROUP TITLE TRACK CHAP. RESUME B.S.P BONUS TUNED STEREO	AUTO MUTING	AUTO	MODE
				A.POSITION

LPCM SUBWFR LFE	kHz
MPEG-2AAC LS S RS	MHz
	VOL

R –21 CENTER L –21

4Repeat steps 2 and 3 to set other items if necessary.

• For details about each item, see below.

7Front speaker output balance

“BAL (balance)”

ANALOG DIGITAL AUTO		PL DSP SLEEP PROGRAM REPEAT 1A-B RANDOM PROGRESSIVE RDS	TA NEWS INFO	INPUT ATT
PPCM AUTO SURROUND				SPK 1	2 RE	C
DIGITAL L C	R	GROUP TITLE TRACK CHAP. RESUME B.S.P BONUS TUNED STEREO	AUTO MUTING	AUTO	MODE
				A.POSITION

LPCM SUBWFR LFE	kHz
MPEG-2AAC LS S RS	MHz
	VOL

If the sounds you hear from the front right and left speakers are unequal, you can adjust the speaker output balance.

SURR R*4	EFFECT*5	AUDIO POS*6
(Surround right)		(Audio position)

(back to the beginning)

*4 These items appear only when the corresponding speakers are set to other than “NONE” as its speaker size.

*5 “EFFECT” appears only when one of DAP modes (see pages 30 and 31) is activated.

*6 “AUDIO POS” appears only when “YES” or “USE” (see pages 23, 25, or 57) is selected for the subwoofer.

Adjust the output balance appropriately from the listening point within the range of R (Right) –21 to CENTER (0) or CENTER (0) to L (Left) –21 (“CENTER” is the initial setting).

Note:

•When you select “R –21,” no sound comes out of the front right speaker, and when you select “L –21,” no sound comes out of the front left speaker.

28