JVC RX-DV31 manual Activating Surround Mode, Selecting Surround Modes, Press Surround Mode

Activating Surround Mode	Press SURROUND MODE.
	• Each time you press the button, Surround mode changes

English

When Auto Surround is set to “OFF” or 2-channel source other than Dolby Surround software is played back, activate Surround mode manually.

Make sure that you have set the speakers’ information correctly (see pages 25 or 57).

•If only front speakers are connected, you cannot activate any Surround mode.

On the front panel From the remote control

as illustrated below.

When 5 or 4 speakers (except center speaker) are connected:

O	PL DSP SLEEP PROGRAM REPEAT 1A-B RANDOM PROGRESSIVE RDS	TA NEWS INFO	INPUT ATT
OUND			SPK 1	2 RE	C
R	GROUP TITLE TRACK CHAP. RESUME B.S.P BONUS TUNED STEREO	AUTO MUTING	AUTO	MODE
			A.POSITION
LFE			kHz
RS			MHz
			VOL

PLII	MOVIE	PLII MUSIC
LIVE CLUB		DANCE CLUB
HALL		PAVILION
ALL CH ST.		(back to the beginning)

Press SURROUND ON/OFF.

When 3 speakers (except surround speakers) are

The SURROUND indicator lights up on the display.connected or Dolby Digital including matrix source is played back:

To cancel the Surround mode

Press SURROUND ON/OFF again.	O	PL DSP SLEEP PROGRAM REPEAT 1A-B RANDOM PROGRESSIVE RDS	TA NEWS INFO INPUT ATT
	OUND	GROUP TITLE TRACK CHAP. RESUME B.S.P BONUS TUNED STEREO	AUTO MUTING	SPK 1	2 RE	C
	R			AUTO	MODE
				A.POSITION

• Surround mode is deactivated (“STEREO” appears on the	LFE	kHz
	RS	MHz
		VOL

display).

About SURROUND indicators

PLII

MOVIE

PLII

MUSIC

• When Auto Surround is set to

ANALOG DIGITAL AUTO

PL DSP SLEEP PRO

“ON,” the AUTO SURROUND

PPCM AUTO SURROUND

GROUP TITLE

TRAC

indicator always lights up on

DIGITAL L C

R

Signal and speaker indicators on the display

LPCM SUBWFR LFE

the display.

MPEG-2 AAC LS S RS

L

C

R

L

C

R

• When you activate Surround

LFE

SUBWFR LFE

DSP SLEEP PRO

mode manually with Auto

ANALOG DIGITAL AUTO

PL

PPCM AUTO SURROUND

GROUP TITLE

TRAC

Surround set to “OFF,” the

DIGITAL L C

R

LS

S

RS

LS

S

RS

LPCM SUBWFR LFE

SURROUND indicator lights

MPEG-2AAC LS S

RS

up on the display.

Signal indicators

Speaker indicators

The following signal indicators light up—:

L, R:

• When digital input is selected: Light up

Selecting Surround Modes

when the signals corresponding to each

When 2-channel source is played back with Surround mode

channel come in.

• When analog input is selected: Always

activated, you can select another Surround mode.

light up.

Available Surround modes will vary depending on the

C, LS, RS:

Light up when the signals corresponding to

number of the connected speakers and the playback sound.

each channel come in.

Make sure that you have set the speakers’ information

S:

Lights up when the monaural surround

correctly (see pages 25 or 57).

channel signal comes in.

• If surround speakers are not connected, you cannot use

LFE:

Lights up when the LFE channel signal

DAP modes and All Channel Stereo.

comes in.

• If you select any of the Surround modes while using both

the speakers connected to the FRONT SPEAKERS 1 and 2

The speaker indicators light up as follows:

terminals, the speakers connected to the FRONT

• The subwoofer speaker indicator ( SUBWFR ) lights up

SPEAKERS 2 terminals are deactivated.

when the subwoofer is set to “YES” (see page 25) or

“USE” (see pages 23 or 57).

• The other speaker indicators light up only when the

corresponding speaker is activated, and also when

required for the current playback.

On the front panel

From the remote control

32