Siemens RDG400 Single duct with radiator or floor heating, Modulating radiator / floor heating

Page 21

4.7.6Single duct with radiator or floor heating

In single duct applications with radiator or floor heating, the thermostat controls a valve plus an auxiliary electrical heater. Parameter P01 is not available.

The output signal for the air flow can be limited to a minimum and maximum value if required (see section 4.6 "additional features").

The air flow starts to rise when the acquired room temperature is above "setpoint" + "dead zone".

The radiator receives an ON command when the acquired room temperature drops below “setpoint” – “dead zone” (= “setpoint for radiator”).

Note: “Setpoint for radiator” is limited by parameter “Maximum heating setpoint” (P10).

Floor heating

The radiator sequence can also be used for floor heating.

 

The "Floor heating limitation function" is described on page 15.

Sequences

ON/OFF radiator / floor heating

Y

 

XpC

C

100%

 

Vmax

max

 

YV

 

Vmin

 

min

 

0%

 

TR [°C]

Y

SDH

ON

YR

Modulating radiator / floor heating

Y

XpC

 

100%

C

 

 

 

Vmax

 

max

 

 

Vmin

YV

 

min

 

 

 

0%

TR [°C]

 

Y

XpH

100%

YR

OFF

W

dz

TR [°C]

 

0%

 

 

W

 

 

 

 

dz

 

TR [°C]

Y

Output signal

TR

Room temperature

WEffective setpoint Comfort

H Heating sequence

C Cooling sequence

YV

Volume flow rate

YR

Radiator / floor heating

XpH

Proportional band heating

XpC

Proportional band cooling

Vmin

Minimum volume output

Vmax

Maximum volume output

Note: The diagrams show the PI controller's proportional part only.

Setting the sequence and the control outputs

Refer to sections 4.5 (applications), 4.7.1 (sequences) and 4.7.3 (outputs).

 

 

21 / 42

 

 

 

Siemens

RDG100, RDG100T, RDG110, RDG140, RDG160 Basic Documentation

CE1P3182en

Building Technologies

Functions

28 May 2009

Image 21
Contents Edition CE1P3182en 28 May Building TechnologiesTable of contents Revision history About this documentReference documents Before you startDocument use / request to the reader Features Types and featuresSummary Brief descriptionEquipment combinations Use AccessoriesOrdering SSA81 SSP81… SSB81 SSD81 SQS85…Functions Temperature controlGeneral note Described in sectionOperating modes Comfort mode Energy Saving Protection modeSetpoints Setpoints and sequence Comfort mode Energy Saving Protection mode ApplicationSingle duct With min/max Limitation Single duct With Electrical HeaterHeating mode Cooling mode Single duct Comfort mode Energy Saving mode ApplicationProtection mode Heating mode Cooling mode With heating Cooling coilApplications overview Additional features External / return air Temperature sensorFloor heating Limitation functionButton lock Sec after the last adjustmentLocked or unlocked by pressing the right button for 3 sec Comf Extension Prot Absence Not available EcoParameter P01 = Sequence Mode Sequences overview setting via parameter P01Control sequences Applications and sequencesSingle-duct heating / cooling coil Function of the control outputs is set via DIP switches 4DIP Y10 = … 10 10 … 0 V inverted PositionSingle duct Setting the sequence and the control outputsHeating or cooling Modulating control 3-position, PWM or DC 0 … 10Single duct with electrical heater SequencesModulating electrical heater Modulating radiator / floor heating Single duct with radiator or floor heatingSingle duct with heating / cooling coil Control sequenceModulating heating / cooling coil Control outputs Control output for air flowSynchronization ON/OFF control signal Position control SignalPosition actuator Parameter P44 Y1 and Y2AI/DI Multifunctional input, Digital inputDIP switches Handling of faultsTemperature out RangeParameter setting Control parametersChange the parameters as follows Service level Parameters Service levelExpert level Parameters Expert level, diagnostics & testDiagnostics & test Wiring Mounting and installationHandling MountingLayout OperationButton operation User actionLCD display DisposalConnection terminals EngineeringConnection diagrams Dimensions Mechanical designGeneral Power supply Outputs Inputs Operational data Technical dataPage Automatic heating/cooling changeover Index