JVC VR 601 instruction manual Alarm In/Out, This Figure is Looked from the Rear, No Connection

Page 14

2.3 ALARM In/Out

DISK FULL

ALARM RESET

 

RECORD IN

 

5

4

9 8

ALARM IN

NO CONNECTION

 

 

ALARM OUT

 

 

GROUND

3

2

1

7 6

SWITCH OUT

NO CONNECTION

*THIS FIGURE IS LOOKED FROM THE REAR

1.GND: Ground Contact.

2.ALARM OUT (OUTPUT): This is an alarm output trigger. Connect this to external devices such

 

 

 

5V

 

as buzzers or lights. (

 

0V(Active)

)

 

3.DISK FULL (OUTPUT): This is a disk full output trigger. Connect this to external devices such

 

 

 

5V

 

as buzzers or lights. (

 

0V(Active)

)

 

4.ALARM RESET (INPUT): This pin connects to an alarm-clear device for clearing an alarm.

(

5V 0V(Active) )

5. RECORD IN (INPUT): This pin connects to a record trigger device for starting a record.

(

5V 0V(Active) )

6.SWITCH OUT (OUTPUT): This pin, sending out timing signals (falling / negative) to a multiplexer, connects to a multiplexer’s trigger terminal so the multiplexer can switch to use the same recording speed as the DVR.

7.NO CONNECTION

8.NO CONNECTION

9.ALARM IN (INPUT): This is an alarm input which can be programmed in the menu system to

Normally Open or Normally Closed. (

 

 

5V

)

 

 

0V(Active)

 

 

14

Image 14
Contents Digital Video Recorder Important Safeguards Safety Precautions for USA and Canada AvertissementImportant In the United Kingdom Mains Supply AC 230 Power SystemFor Your Safety Australia Connection to the mains supplyHandling the unit About the provided power cables for VR-601 UPlace of storage and use Important Safety Instructions AC adapter sectionTable Of Contents Specifications Compatible Multiplexers Product Features Product IntroductionHard-disk compartment lock Front ViewHard-disk drive compartment Operate buttonOperate Indicator Rec IndicatorDisk Indicator Up / Down buttonsMobile Rack Power LED Mobile Rack HDD LEDRear View No Connection Alarm In/OutThis Figure is Looked from the Rear Memo Basic ConnectionConnectiong to the AC Adapter Connecting with a Single Camera Connecting with a MultiplexerConnecting with a Quad MultiplexerAttaching AN External Device to DVR Clock SETHard-Disk Drive Installation MaxtorMUX OFF Size POS System InformationQuality Best Ntsc Rate 6 HR Updating System Software High Configuring Recording SettingsBest StandardNtsc MUX OFF PAL MUX OFF Manual Recording Timer RecordingRecording Operations Start END 0000-0000 M 0000-0000 W 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000Externally triggered Recording Alarm RecordingPRE- Alarm OFF Main Alarm REC Enable REC Quality Best Audio OFF ALM Type ALM DurationDiagrams below Fast Forward/Reverse Operation Status From REC mode to Playback modePlayback Operations Search to play back a particular recorded videoPlay Back Picture-by-picture You can also operate by using button and buttonSlow Forward/Reverse Play Back Recorded Video from a HDD of the mobile rack Search Full List Alarm List Time Search Thumbnail SD CardSearch Operations Full List SearchTime Search Alarm list SearchAlarm List Search2003 Thumbnail SearchSearch Thumbnail Year Full List SD Card Search Backup Backup Main SET HD2 Usage Backup OperationsMobile Rack HD Backup Alarm Select Main Backup ALL to HD2Search button Alarm Select Main Backup Alarm to HD2Disk Setting Reformat HD2 Usage 1220 2001-02-01 0330 2001-03-02 0420 1330Save the whole setting into the SD card Security Digital Card SD Card BackupBackup the System setting info into SD Card Archive Single image Clips into SD CardTransfer the system setting info of DVR to another Key Lock OperationMenu Setup REC Setting REC QualityAlarm Setting REC Quality PRE- Alarm Timer Clock / TimerClock / Timer SET REC Enable OFF Main Timer REC Enable REC ScheduleCommunication NET Enable OFF NET Dhcp NET IP SET FTP Setting MainNET Enable REC Mode Alarm REC Comm Setting FTP Setting Comm IDEnable REC ModeUser PasswordFTP Account FTP IP PathBackup HD HD2 Usage Disk SettingBackup Full Main Disk REFORMAT/CLEAR BackupSystem Situation MAC 00 0c 0c 00 00 Bios SW 1.00J Date Jun 9 Communication Protocol SetupGeneral Command Format Value of a specific front panel key Request State Second Category=0x06 Request Time Second Category=0x02Set Time Second Category=0x02 Description of System StateMobile Rack Installation Jumper settings of hard-disk drives for the system LocationPage Push the active-handle inward Lock the Key System Default Disk Setting Reformat SET RS232 / RS485D Message Meanings Network Viewer PIN noPage View the VR-601 video from a remote PC Viewing images View all the connected devices Function Buttons DescriptionView single device Playback function bar Set the Alarm record settings Change the Record & Timer Properties Via the NetworkSet the regular record settings Set the record timerArchive Images to the Computer Image Viewer 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Point stops recording Previously recorded data remainingConnect to a computer Physical specification of RJ-45 cable for EthernetCable Connections Connect to a LAN Hub IntranetEnable DVR Network Function RJ-45 PIN configuration for LAN HubConfigure Your DVR Network Settings Connect to WAN InternetEnable Dhcp Function Set IP Address12.3 TCP/IP Communication Software Page Click Start Settings Control Panel Network 12.4 TCP/IP installation12.5 TCP/IP Configuration setting Connection Testing Click Start Programs MS-DOS PromptPage Design and specifications subject to change without notice Model Number VR-601 U VR-601 EDecode on Manufacturer Model ChannelColors DVR Viewer