JVC VR 601 instruction manual SD Card Search

Page 35

4.4.5 SD CARD Search

Take the following steps to proceed with the SD card search function.

(1)Insert a SD Card into the SD card slot of the rear unit.

(2)Press the Search button to enter the search mode.

(3)Select the SD CARD and press the Enter button to access the complete list of JPG files.

(4)Highlight the specific JPG file of your requirement and press the Enter button to display the image.

(5)If you need another, please return to the SD card JPG file list page and repeat steps (3) and

(4) again for another search.

FULL LIST

ALARM LIST TIME SEARCH THUMBNAIL SD CARD

SD CARD JPG FILE

F0000.JPG

F0001.JPG

F0002.JPG

F0003.JPG

F0004.JPG

F0005.JPG

NOTE: If you would like to delete JPG file in the SD card, please return to SD CARD JPG FILE list page and highlight the specific JPG file of your requirement and press the Setup button and then select the “Yes” to delete the image.

*About the location of the buttons, please refer to Page 10 2.1 Front View.

Image 35

Contents Digital Video Recorder Important Safeguards Avertissement Safety Precautions for USA and CanadaConnection to the mains supply Power SystemFor Your Safety Australia Important In the United Kingdom Mains Supply AC 230Handling the unit About the provided power cables for VR-601 UPlace of storage and use AC adapter section Important Safety InstructionsTable Of Contents Specifications Compatible Multiplexers Product Introduction Product FeaturesOperate button Front ViewHard-disk drive compartment Hard-disk compartment lockUp / Down buttons Rec IndicatorDisk Indicator Operate IndicatorMobile Rack HDD LED Mobile Rack Power LEDRear View No Connection Alarm In/OutThis Figure is Looked from the Rear Memo Basic ConnectionConnectiong to the AC Adapter Connecting with a Multiplexer Connecting with a Single CameraMultiplexer Connecting with a QuadClock SET Attaching AN External Device to DVRMaxtor Hard-Disk Drive InstallationMUX OFF Size POS System InformationQuality Best Ntsc Rate 6 HR Updating System Software Standard Configuring Recording SettingsBest HighNtsc MUX OFF PAL MUX OFF Manual Recording Timer RecordingRecording Operations Start END 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 M 0000-0000 WREC Quality Best Audio OFF ALM Type ALM Duration Alarm RecordingPRE- Alarm OFF Main Alarm REC Enable Externally triggered RecordingDiagrams below Search to play back a particular recorded video Operation Status From REC mode to Playback modePlayback Operations Fast Forward/ReversePlay Back Picture-by-picture You can also operate by using button and buttonSlow Forward/Reverse Full List Search Search Full List Alarm List Time Search Thumbnail SD CardSearch Operations Play Back Recorded Video from a HDD of the mobile rackSearch Alarm list SearchAlarm List Time Search2003 Thumbnail SearchSearch Thumbnail Year Full List SD Card Search Alarm Select Main Backup ALL to HD2 Backup OperationsMobile Rack HD Backup Backup Backup Main SET HD2 Usage1220 2001-02-01 0330 2001-03-02 0420 1330 Alarm Select Main Backup Alarm to HD2Disk Setting Reformat HD2 Usage Search buttonArchive Single image Clips into SD Card Security Digital Card SD Card BackupBackup the System setting info into SD Card Save the whole setting into the SD cardKey Lock Operation Transfer the system setting info of DVR to anotherMenu Setup REC Quality REC SettingAlarm Setting REC Quality PRE- Alarm REC Schedule Clock / TimerClock / Timer SET REC Enable OFF Main Timer REC Enable TimerCommunication NET Enable OFF NET Dhcp NET IP SET FTP Setting MainNET Enable REC Mode Comm Setting FTP Setting Comm IDEnable REC Mode Alarm RECPath PasswordFTP Account FTP IP UserBackup Disk SettingBackup Full Main Disk REFORMAT/CLEAR Backup HD HD2 UsageSystem Situation MAC 00 0c 0c 00 00 Bios SW 1.00J Date Jun 9 Communication Protocol SetupGeneral Command Format Value of a specific front panel key Description of System State Request Time Second Category=0x02Set Time Second Category=0x02 Request State Second Category=0x06Jumper settings of hard-disk drives for the system Location Mobile Rack InstallationPage Push the active-handle inward Lock the Key System Default SET RS232 / RS485 Disk Setting ReformatD Message Meanings PIN no Network ViewerPage View the VR-601 video from a remote PC Function Buttons Description Viewing images View all the connected devicesView single device Playback function bar Set the record timer Change the Record & Timer Properties Via the NetworkSet the regular record settings Set the Alarm record settingsArchive Images to the Computer Image Viewer Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03Connect to a LAN Hub Intranet Physical specification of RJ-45 cable for EthernetCable Connections Connect to a computerConnect to WAN Internet RJ-45 PIN configuration for LAN HubConfigure Your DVR Network Settings Enable DVR Network FunctionSet IP Address Enable Dhcp Function12.3 TCP/IP Communication Software Page Click Start Settings Control Panel Network 12.4 TCP/IP installation12.5 TCP/IP Configuration setting Click Start Programs MS-DOS Prompt Connection TestingPage Model Number VR-601 U VR-601 E Design and specifications subject to change without noticeDVR Viewer Manufacturer Model ChannelColors Decode on