JVC VR 601 instruction manual Place of storage and use, Handling the unit

Page 5

SAFETY PRECAUTIONS

Place of storage and use

Please avoid storing or using this DVR in the following places:

Extremely hot or cold places beyond the allowable temperature for operation (5°C – 40°C).

Humid or dry places beyond the allowable humidity range for operation (30% –80% RH). Dusty or sandy places.

Places exposed to oil, smoke or steam, such as the kitchen vicinity.

Intensely vibrating or unstable places. Places prone to condensation.

Places that generate strong magnetic fields, e.g., transformer or motor.

Places near devices that generate electric waves, e.g., transceiver or mobile phone. Places that generate radiation, X-rays or corrosive gases.

Handling the unit

Please do not place heavy objects on the DVR, like a monitor or TV.

Please keep the mobile rack into the compartment. As injury may result from fingers getting clamped.

Please do not block the ventilation openings. Avoid violent shocks to the unit. Do not drop the unit.

Please remove the AC adapter to save energy when the unit is not in use.

Maintaining the unit (Please turn off the power before performing maintenance work.)

Please wipe the unit with a soft cloth. Do not wipe it with thinner or benzene lest the surface melts or becomes dull. For stubborn stains, wipe first with a water-diluted neutral detergent and then wipe dry.

About the provided power cables (for VR-601 U)

Two power cables are provided with the VR-601 U. Use the one that corresponds to your power – supply.

When usage voltage is 120V or less; use the A – type (flat – pin type).power cable.

When usage voltage is 127V or over; use the C – type (round – pin type).power cable.

Please use the provided AC adapter to connect the DVR to a power source.

Please use the supplied power cord. Using a different type or damaged cord may cause fire or electric shock.

Hard-disk

The hard-disk is a consumable item. Replacement is recommended after 10000 hours of use ( if used in a 25C environment ). For information on maintenance planning and costs, consult your nearest JVC dealer.

To save energy, be sure to turn off the system when not in use.

5

Image 5
Contents Digital Video Recorder Important Safeguards Avertissement Safety Precautions for USA and CanadaFor Your Safety Australia Power SystemImportant In the United Kingdom Mains Supply AC 230 Connection to the mains supplyHandling the unit About the provided power cables for VR-601 UPlace of storage and use AC adapter section Important Safety InstructionsTable Of Contents Specifications Compatible Multiplexers Product Introduction Product FeaturesHard-disk drive compartment Front ViewHard-disk compartment lock Operate buttonDisk Indicator Rec IndicatorOperate Indicator Up / Down buttonsMobile Rack HDD LED Mobile Rack Power LEDRear View No Connection Alarm In/OutThis Figure is Looked from the Rear Memo Basic ConnectionConnectiong to the AC Adapter Connecting with a Multiplexer Connecting with a Single CameraMultiplexer Connecting with a QuadClock SET Attaching AN External Device to DVRMaxtor Hard-Disk Drive InstallationMUX OFF Size POS System InformationQuality Best Ntsc Rate 6 HR Updating System Software Best Configuring Recording SettingsHigh StandardNtsc MUX OFF PAL MUX OFF Manual Recording Timer RecordingRecording Operations Start END 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 M 0000-0000 WPRE- Alarm OFF Main Alarm REC Enable Alarm RecordingExternally triggered Recording REC Quality Best Audio OFF ALM Type ALM DurationDiagrams below Playback Operations Operation Status From REC mode to Playback modeFast Forward/Reverse Search to play back a particular recorded videoPlay Back Picture-by-picture You can also operate by using button and buttonSlow Forward/Reverse Search Operations Search Full List Alarm List Time Search Thumbnail SD CardPlay Back Recorded Video from a HDD of the mobile rack Full List SearchAlarm List Alarm list SearchTime Search Search2003 Thumbnail SearchSearch Thumbnail Year Full List SD Card Search Mobile Rack HD Backup Backup OperationsBackup Backup Main SET HD2 Usage Alarm Select Main Backup ALL to HD2Disk Setting Reformat HD2 Usage Alarm Select Main Backup Alarm to HD2Search button 1220 2001-02-01 0330 2001-03-02 0420 1330Backup the System setting info into SD Card Security Digital Card SD Card BackupSave the whole setting into the SD card Archive Single image Clips into SD CardKey Lock Operation Transfer the system setting info of DVR to anotherMenu Setup REC Quality REC SettingAlarm Setting REC Quality PRE- Alarm Clock / Timer SET REC Enable OFF Main Timer REC Enable Clock / TimerTimer REC ScheduleCommunication NET Enable OFF NET Dhcp NET IP SET FTP Setting MainNET Enable Enable Comm Setting FTP Setting Comm IDREC Mode Alarm REC REC ModeFTP Account FTP IP PasswordUser PathBackup Full Main Disk REFORMAT/CLEAR Disk SettingBackup HD HD2 Usage BackupSystem Situation MAC 00 0c 0c 00 00 Bios SW 1.00J Date Jun 9 Communication Protocol SetupGeneral Command Format Value of a specific front panel key Set Time Second Category=0x02 Request Time Second Category=0x02Request State Second Category=0x06 Description of System StateJumper settings of hard-disk drives for the system Location Mobile Rack InstallationPage Push the active-handle inward Lock the Key System Default SET RS232 / RS485 Disk Setting ReformatD Message Meanings PIN no Network ViewerPage View the VR-601 video from a remote PC Function Buttons Description Viewing images View all the connected devicesView single device Playback function bar Set the regular record settings Change the Record & Timer Properties Via the NetworkSet the Alarm record settings Set the record timerArchive Images to the Computer Image Viewer Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03Cable Connections Physical specification of RJ-45 cable for EthernetConnect to a computer Connect to a LAN Hub IntranetConfigure Your DVR Network Settings RJ-45 PIN configuration for LAN HubEnable DVR Network Function Connect to WAN InternetSet IP Address Enable Dhcp Function12.3 TCP/IP Communication Software Page Click Start Settings Control Panel Network 12.4 TCP/IP installation12.5 TCP/IP Configuration setting Click Start Programs MS-DOS Prompt Connection TestingPage Model Number VR-601 U VR-601 E Design and specifications subject to change without noticeColors Manufacturer Model ChannelDecode on DVR Viewer