JVC VR 601 Mobile Rack Installation, Jumper settings of hard-disk drives for the system Location

Page 56

7. Mobile Rack Installation

Usually, the unit comes with one hard-disk drive installed in compartment HD 1, which is default-configured as a master. The jumper settings configuration of the installed hard-disk drives for the unit and compatible drives which can be used with this unit are listed in the table below. To install a hard-disk drive in compartment HD 2, please take the following steps.

The jumper settings of hard-disk drives for the system

 

 

Location

Jumper

 

IDE 1

Compartment HD 1

Master

 

IDE 2

Compartment HD 2

Master

 

 

 

 

 

 

 

 

1. Make sure that the key unlocked.

2.Pull the active-handle outward to remove the carrier body away from the mobile rack

3. Slide the top cover backward and remove.

4.Setting the jumper of your hard-disk drive. The way to set the jumper of the drive varies between manufacturers; please refer to the instructions on the drive to set the jumpers in the master position.

56

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Digital Video Recorder Important Safeguards Safety Precautions for USA and Canada AvertissementPower System For Your Safety AustraliaImportant In the United Kingdom Mains Supply AC 230 Connection to the mains supplyHandling the unit About the provided power cables for VR-601 UPlace of storage and use Important Safety Instructions AC adapter sectionTable Of Contents Specifications Compatible Multiplexers Product Features Product IntroductionFront View Hard-disk drive compartmentHard-disk compartment lock Operate buttonRec Indicator Disk IndicatorOperate Indicator Up / Down buttonsMobile Rack Power LED Mobile Rack HDD LEDRear View No Connection Alarm In/OutThis Figure is Looked from the Rear Memo Basic ConnectionConnectiong to the AC Adapter Connecting with a Single Camera Connecting with a MultiplexerConnecting with a Quad MultiplexerAttaching AN External Device to DVR Clock SETHard-Disk Drive Installation MaxtorMUX OFF Size POS System InformationQuality Best Ntsc Rate 6 HR Updating System Software Configuring Recording Settings BestHigh StandardNtsc MUX OFF PAL MUX OFF Manual Recording Timer RecordingRecording Operations Start END 0000-0000 M 0000-0000 W 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000Alarm Recording PRE- Alarm OFF Main Alarm REC EnableExternally triggered Recording REC Quality Best Audio OFF ALM Type ALM DurationDiagrams below Operation Status From REC mode to Playback mode Playback OperationsFast Forward/Reverse Search to play back a particular recorded videoPlay Back Picture-by-picture You can also operate by using button and buttonSlow Forward/Reverse Search Full List Alarm List Time Search Thumbnail SD Card Search OperationsPlay Back Recorded Video from a HDD of the mobile rack Full List SearchAlarm list Search Alarm ListTime Search Search2003 Thumbnail SearchSearch Thumbnail Year Full List SD Card Search Backup Operations Mobile Rack HD BackupBackup Backup Main SET HD2 Usage Alarm Select Main Backup ALL to HD2Alarm Select Main Backup Alarm to HD2 Disk Setting Reformat HD2 UsageSearch button 1220 2001-02-01 0330 2001-03-02 0420 1330Security Digital Card SD Card Backup Backup the System setting info into SD CardSave the whole setting into the SD card Archive Single image Clips into SD CardTransfer the system setting info of DVR to another Key Lock OperationMenu Setup REC Setting REC QualityAlarm Setting REC Quality PRE- Alarm Clock / Timer Clock / Timer SET REC Enable OFF Main Timer REC EnableTimer REC ScheduleCommunication NET Enable OFF NET Dhcp NET IP SET FTP Setting MainNET Enable Comm Setting FTP Setting Comm ID EnableREC Mode Alarm REC REC ModePassword FTP Account FTP IPUser PathDisk Setting Backup Full Main Disk REFORMAT/CLEARBackup HD HD2 Usage BackupSystem Situation MAC 00 0c 0c 00 00 Bios SW 1.00J Date Jun 9 Communication Protocol SetupGeneral Command Format Value of a specific front panel key Request Time Second Category=0x02 Set Time Second Category=0x02Request State Second Category=0x06 Description of System StateMobile Rack Installation Jumper settings of hard-disk drives for the system LocationPage Push the active-handle inward Lock the Key System Default Disk Setting Reformat SET RS232 / RS485D Message Meanings Network Viewer PIN noPage View the VR-601 video from a remote PC Viewing images View all the connected devices Function Buttons DescriptionView single device Playback function bar Change the Record & Timer Properties Via the Network Set the regular record settingsSet the Alarm record settings Set the record timerArchive Images to the Computer Image Viewer 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Point stops recording Previously recorded data remainingPhysical specification of RJ-45 cable for Ethernet Cable ConnectionsConnect to a computer Connect to a LAN Hub IntranetRJ-45 PIN configuration for LAN Hub Configure Your DVR Network SettingsEnable DVR Network Function Connect to WAN InternetEnable Dhcp Function Set IP Address12.3 TCP/IP Communication Software Page Click Start Settings Control Panel Network 12.4 TCP/IP installation12.5 TCP/IP Configuration setting Connection Testing Click Start Programs MS-DOS PromptPage Design and specifications subject to change without notice Model Number VR-601 U VR-601 EManufacturer Model Channel ColorsDecode on DVR Viewer
Top Page Image Contents